Restraints Wiring Repairs

Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
We've separated the vehicle makers into two groups: those that do not allow restraints wiring repairs and those that allow restraints wiring repairs.
Do NOT Repair
Genesis
Per Genesis service manuals: "Never attempt to modify, splice, or repair SRS wiring. If there is an open or damage in SRS wiring, replace the harness."
Honda / Acura
Per the Honda and Acura repair information states: "Never attempt to modify, splice, or repair airbag system wiring. If airbag system wiring is damaged, replace the wiring harness(es)."
Hyundai
Per the Hyundai service information: "Never attempt to modify, splice, or repair SRS wiring. If there is an open or damage to the SRS wiring, replace the harness."
Jaguar Land Rover
Per the Jaguar and Land Rover Workshop manuals: "Given the legal implications of a restraints system failure, harness repairs to Air Bag module circuits are not acceptable. Where the text refers to "REPAIR the circuit", this will normally mean the replacement of a harness."
Kia
Per Kia service manuals: "SRS wiring can be identified by special yellow outer covering. Observe the instructions described in this section. Never attempt to modify, splice, or repair SRS wiring. If there is an open or damage in SRS wiring, replace the harness."
Maserati
Per a Maserati service bulletin: "Maserati does not allow any repairs to airbag system wiring harnesses, connectors, or terminals. If any damage is found on an airbag harness, connector or wire terminal, it must be replaced... It is forbidden to repair (solder) any electrical connections that affect devices involved in the active safety of the vehicle, unless prior express authorization from Maserati Technical Service is obtained."
Mazda
Per the Mazda service information: "Incorrectly repairing an air bag wiring harness can accidentally operate (deploy) the air bag module and pre-tensioner front buckles. If a problem is found in the air bag wiring harness, always replace the wiring harness with a new one."
Mitsubishi
Per the Mitsubishi service information: "Do not attempt to repair the wiring harness connectors of the SRS. If any of the connectors are diagnosed as faulty, replace the wiring harness. If the wires are diagnosed as faulty, replace or repair the wiring harness according to the following table." The table can be found in the Mitsubishi repair information.
Subaru
Per Subaru service information: "If damage, open circuit or rust is found on airbag system wiring harness, do not repair the harness. Always replace the faulty harness with a new genuine part."
Toyota / Lexus / Scion
Per Toyota CRIB #160 SRS Precautions: "Never repair SRS wiring or connectors. Replace damaged wiring."
Volkswagen
Per the Volkswagen position statement, Supplemental Restraint System Wiring Harnesses Applicable To All Volkswagen Models: "Do NOT attempt to repair the SRS wiring system or related components on any Volkswagen vehicle. Replace any damaged or bent SRS components with Genuine Volkswagen Parts. Some fasteners and clips are non-reusable; refer to the Volkswagen repair manual for more information."
Repairs Allowed
Audi
Per the Audi repair manual: "The airbag and seat belt tensioner system can fail.
- Faulty repairs performed on airbag and seat belt tensioner system can lead to malfunction in passenger protection.
- When performing repairs on airbag and seat belt tensioner wiring harness, use only terminals, connectors and wires designated for it. Refer to the Parts Catalog."
BMW / Mini
Per BMW service information: "Only repair those cables which show visible signs of damage. In the event of visible damage, make sure there is only one cable repair in effect after the repair work. If no visible damage can be identified, the entire cable must be replaced. When carrying out repairs to the airbag wiring harness, you must use the spare parts offered in the Electronic Parts Catalogue (EPC)."
Chevrolet / Cadillac / Buick / GMC
Per the General Motors (GM) service information Document ID 325229 - SIR/SRS Wiring Repairs: "The Supplemental Inflatable Restraint (SIR) System/Supplemental Restraint System (SRS) requires special wiring repair procedures due to the sensitive nature of the circuitry. Follow the specific procedures and instructions when working with the SIR/SRS, and the wiring components, such as connectors and terminals."
Fiat / Chrysler / Dodge / Jeep / RAM / Alfa Romeo
Per FCA/Stellantis service information: "It is important when repairing any Supplemental Restraint System (SRS) electrical circuits to use the recommended splicing kit and procedure.
This recommended procedure involves crimping the wires together with a splice band, soldering the crimped connection and, finally, sealing and protecting the repair. The crimp and solder ensure a strong mechanical bond that will always pass a pull test while also maintaining the conductivity and current carrying capacity of the circuit. The adhesive sealant and heat shrink tubing ensures the splice repair will perform as well or better than the original wire and be safe from potential corrosion or short circuits.
There is no limit to the number of splice repairs that can be made in one harness using this procedure. However, as has been past practice, multiple adjacent splices should be offset from each other. This wiring splice repair procedure is approved for harness side repairs only. Repairs and splices to pigtail wires on SRS components such as airbag units, seat belt tensioner units or clocksprings are not approved or recommended."
Ford / Lincoln
Per our contacts at Ford: "Refer to Ford service information regarding SRS system wiring and connectors. Ford Technical Service Bulletin (TSB) 05-18-7 (August 29, 2005), states that if restraints connectors or wiring are contained in:
- a stand-alone harness, do not repair them. Replace the restraints harness unless directed to repair the circuit by a TSB or other Ford publication.
- the main vehicle wiring harnesses, they should be repaired using the solder and heat-shrink repair procedures in this TSB. The General Wire Terminal Repair Kit contains gold-plated terminated pigtails (with white insulation) and dual-wall heat-shrink tubing to perform these repairs. Loaded wiring pigtail kits with goldplated terminals are also available in the parts catalog."
Mercedes-Benz / Smart
Per the Mercedes-Benz service information: "The SRS wire harness pigtail is replaced using solder connectors. Contact a Mercedes-Benz part dealer."
Nissan / INFINITI
Per Nissan/INFINITI TechTalk summary document, TT Harness Repair Kit: "Nissan/INFINITI now allow repairs to SRS connectors and wire overlays of most circuits. Wiring harness and connector repair procedures have been expanded to improve customer satisfaction by simplifying the repair of most electrical wiring harnesses, which is the preferred alternative to wiring harness replacement."
Rolls-Royce
Per Rolls-Royce: “Only repair those cables which show visible signs of damage. In the event of visible damage, make sure there is only one wire repair in effect after the repair work. If no visible damage can be identified, the entire cable must be replaced. When carrying out repairs to the airbag wiring harness, you must use the spare parts offered in the Electronic Parts Catalog (EPC)."
Tesla
Restraints wiring repairs are available but will need to be done by a qualified Tesla specialist or facility.
Tesla states in vehicle-specific collision repair procedures: "The wires listed below are not repairable. Replace the entire wiring harness if there is damage to any of these wires:
- Airbag sensor and seat sensor
- High-voltage (HV) circuits"
Volvo
Per the Volvo service information: "Caution! As the SRS system is a safety system, it is extremely important that these instructions are carefully followed when carrying out repairs in the cable harness."
Related I-CAR Courses
-
Pre- and Post-Repair System Scanning Position Statements
Wednesday, 09 January 2019
Are you wondering if a particular OEM or organization has a published position statement on pre-repair and post-repair scanning? We have compiled a list of most of the position statements…
-
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning
Thursday, 28 July 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
-
ADAS, Calibration, And Scanning Article Hotspot
Monday, 14 January 2019
Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s…
-
Typical Calibration Requirements For Blind Spot Sensors
Wednesday, 19 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Restraints Wiring Repairs
Monday, 23 May 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
-
Typical Calibration Requirements For Forward Radar Sensors
Wednesday, 12 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
MIG Brazing What Is It, Why Should I Use It?
Monday, 02 June 2014
Why MIG Brazing? It is widely known that GMA welded; fully galvanized steel will lose some of its properties, including corrosion protection, due to the heat created during welding. OEMs…
-
Honda/Acura Position Statement: Pre- and Post-Repair System Scanning - UPDATE
Wednesday, 22 May 2019
Honda /Acura have updated their position statement on pre- and post-repair scanning to give more clarification on what is expected for scanning.
-
Typical Calibration Requirements For Park Assist Sensors
Monday, 31 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Mazda I-ELOOP Overview
Monday, 27 January 2014
Beginning model year 2014, Mazda has introduced a regenerative engine braking system called i-ELOOP, short for "Intelligent Energy Loop." In this system, a capacitor is used to store electrical energy…
-
Back-To-Basics: Considerations For Choosing The Right Spraybooth
Friday, 24 March 2023
Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. When it comes to choosing the right spraybooth, there are a few considerations.
-
Hyundai/Genesis Releases Additional Body Repair Manuals: UPDATE
Wednesday, 22 March 2023
Hyundai Motor America has updated their approved body repair manuals (BRMs) available to the United States market. This also includes the new addition of Genesis branded BRMs!
-
I-CAR Repairers Realm: Spray Gun Operation and Maintenance - Coming Soon
Tuesday, 21 March 2023
I-CAR is having a discussion on spray gun operation and maintenance. Tune into Repairers Realm to listen and join in for questions and answers.
-
OEM Emergency Response Guides: Jaguar Land Rover
Friday, 17 March 2023
Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to…
-
Corrosion Protection Guidelines: Maserati
Thursday, 16 March 2023
A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots, that left untreated…
-
I-CAR Repairers Realm: Paint Booth And Fresh Air Filtration System Overview - Now Available
Tuesday, 14 March 2023
I-CAR had a discussion on paint booth fresh air filtration systems.
-
Honda Has Released the 2023 HR-V Model Body Repair News
Wednesday, 08 March 2023
Honda has released a Body Repair News bulletin for the 2023 Honda HR-V. This document provides relevant repair information at a glance for this redesigned vehicle.
-
Acura Has Released The 2023 Integra Body Repair News
Wednesday, 08 March 2023
Acura has released a Body Repair News bulletin for the 2023 Acura Integra. This document provides relevant repair information at a glance for this new vehicle.
-
Locating OEM-Approved HV Tools: Mercedes-Benz
Tuesday, 07 March 2023
When researching procedures for disabling a high-voltage (HV) vehicle, you may notice that many of the procedures require the use of specific tools. Some of them are OEM-specific tools or…
-
GM Repair Insights: Winter 2023
Friday, 03 March 2023
The winter 2023 edition of the General Motors (GM) Repair Insights magazine is now available.
- 2023
- March 2023 (12)
- February 2023 (10)
- January 2023 (11)
- 2022
- December 2022 (11)
- November 2022 (12)
- October 2022 (11)
- September 2022 (13)
- August 2022 (12)
- July 2022 (11)
- June 2022 (13)
- May 2022 (11)
- April 2022 (12)
- March 2022 (12)
- February 2022 (12)
- January 2022 (13)
- 2021
- December 2021 (15)
- November 2021 (12)
- October 2021 (13)
- September 2021 (15)
- August 2021 (12)
- July 2021 (16)
- June 2021 (17)
- May 2021 (14)
- April 2021 (15)
- March 2021 (21)
- February 2021 (15)
- January 2021 (14)
- 2020
- December 2020 (14)
- November 2020 (17)
- October 2020 (12)
- September 2020 (14)
- August 2020 (12)
- July 2020 (18)
- June 2020 (16)
- May 2020 (14)
- April 2020 (20)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)
- 2019
- December 2019 (13)
- November 2019 (19)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (21)
- May 2019 (19)
- April 2019 (21)
- March 2019 (21)
- February 2019 (21)
- January 2019 (18)
- 2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (22)
- July 2018 (21)
- June 2018 (21)
- May 2018 (19)
- April 2018 (19)
- March 2018 (22)
- February 2018 (17)
- January 2018 (20)
- 2017
- December 2017 (15)
- November 2017 (15)
- October 2017 (19)
- September 2017 (20)
- August 2017 (21)
- July 2017 (18)
- June 2017 (23)
- May 2017 (20)
- April 2017 (15)
- March 2017 (18)
- February 2017 (11)
- January 2017 (13)
- 2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (11)
- August 2016 (11)
- July 2016 (8)
- June 2016 (13)
- May 2016 (11)
- April 2016 (11)
- March 2016 (13)
- February 2016 (11)
- January 2016 (9)
- 2015
- December 2015 (10)
- November 2015 (8)
- October 2015 (10)
- September 2015 (7)
- August 2015 (11)
- July 2015 (10)
- June 2015 (8)
- May 2015 (8)
- April 2015 (9)
- March 2015 (8)
- February 2015 (9)
- January 2015 (11)
- 2014
- December 2014 (12)
- November 2014 (7)
- October 2014 (12)
- September 2014 (10)
- August 2014 (9)
- July 2014 (12)
- June 2014 (9)
- May 2014 (14)
- April 2014 (9)
- March 2014 (6)
- February 2014 (1)
- January 2014 (27)