Aluminum Roof Replacement On The Mitsubishi Lancer Evolution And Outlander

The use of dissimilar metals together in one area of the vehicle structure, and the attachment methods used with those materials, can affect damage analysis and repair versus replace decisions. Two models from Mitsubishi that require these considerations are the Lancer Evolution and Outlander.
The Lancer Evolution and Outlander are equipped with an aluminum roof, on models without a sunroof (see Figures 1 and 2). On models with a sunroof, the roof panel is made from steel. On vehicles with an aluminum roof, the roof panel is attached to steel roof rails and roof bows.
According to the 2008-2010 Lancer Evolution and 2007-2010 Outlander Body Repair Manuals, the aluminum roof panel is made from a type of aluminum containing magnesium, copper, and silicon. The manuals state that this type of aluminum has the equivalent strength of cold-rolled steel sheets.
Roof Panel Attachment
The aluminum roof panel is rivet-bonded to the front, side, and rear roof rails, and bonded with adhesive alone to the inner sides of the front and rear roof rails and to the center roof bow. Self-piercing rivets (SPRs) are used for the factory rivet-bonding attachment.
Roof Panel Removal
Following the removal of the SPRs, the roof panel is ready to be separated from the body at the bonded locations. To assist in the removal process, heat can be used in the bonded area of the damaged panel with a flameless heat source up to 204°C (400°F). As the adhesive gets warmer, its strength and bond will weaken. Heating above 204°C (400°F) may weaken high-strength steels and aluminum. The lower center roof bow on the Lancer Evolution, and the inner side roof rails on both the Lancer Evolution and the Outlander are high-strength steel parts.
Installing a Replacement Roof Panel
Figure 2 - (Mitsubishi media photo) This 2008 Mitsubishi Outlander has a rivet-bonded aluminum roof panel.Blind rivets and adhesives are used for the replacement roof panel attachment. The recommended rivet diameter is 4.8 mm.
The adhesive used for the rivet-bonding is different from that used for the attachment areas with just adhesive. The Lancer Evolution and Outlander body repair manuals state to use an epoxyayresin structural adhesive for the rivet-bonding attachment, specifically 3M AAD Part No. 8115 or equivalent. For the adhesive bonding attachment, a urethane body sealer, specifically 3M AAD Part No. 08360 or equivalent is recommended.
The recommended adhesives are applied to the appropriate locations, noted in the repair manual. The adhesive maker's recommendations should be followed for part preparation.
For specific instructions, refer to the vehicle maker's technical information at www.mitsubishitechinfo.com. This is a subscription-based web site. Subscriptions are available for one day, seven days, 30 days, six months, or one year.
Conclusion
Estimators, auto physical damage appraisers, and collision repair technicians must provide complete and accurate diagnosis and repairs to maintain the reliability of a vehicle structure. Damage analysis and repair versus replace decisions have become more challenging because of the increased use of dissimilar materials in vehicle construction, such as the rivet-bonded aluminum roof panel on some Mitsubishi Lancer Evolution and Outlander models.
Photos courtesy of Mitsubishi Motors North America, Inc.
This article first appeared in the March 31, 2010 edition of the I-CAR Advantage Online.
Related I-CAR Courses
-
Pre- and Post-Repair System Scanning Position Statements
Wednesday, 09 January 2019
Are you wondering if a particular OEM or organization has a published position statement on pre-repair and post-repair scanning? We have compiled a list of most of the position statements…
-
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning
Thursday, 28 July 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
-
ADAS, Calibration, And Scanning Article Hotspot
Monday, 14 January 2019
Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s…
-
Restraints Wiring Repairs
Monday, 23 May 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
-
Typical Calibration Requirements For Blind Spot Sensors
Wednesday, 19 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Honda/Acura Position Statement: Pre- and Post-Repair System Scanning - UPDATE
Wednesday, 22 May 2019
Honda /Acura have updated their position statement on pre- and post-repair scanning to give more clarification on what is expected for scanning.
-
Typical Calibration Requirements For Forward Radar Sensors
Wednesday, 12 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
MIG Brazing What Is It, Why Should I Use It?
Monday, 02 June 2014
Why MIG Brazing? It is widely known that GMA welded; fully galvanized steel will lose some of its properties, including corrosion protection, due to the heat created during welding. OEMs…
-
FCA/Stellantis Position Statement: Pre- and Post-Repair System Scanning
Thursday, 09 June 2016
FCA/Stellantis has released a position statement related to pre- and post-repair system scanning.
-
Typical Calibration Requirements For Park Assist Sensors
Monday, 31 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
OEM Emergency Response Guides: Rivian
Wednesday, 20 September 2023
Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to…
-
I-CAR Repairers Realm: Lucid Motors Innovative Vehicles and Repair Network - Coming Soon
Tuesday, 19 September 2023
I-CAR is having a discussion on Lucid Motors innovative vehicles and repair network. Tune into Repairers Realm to listen and join in for questions and answers.
-
Locating ADAS Information: GM - UPDATE
Friday, 15 September 2023
As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern…
-
Hyundai/Genesis Releases Additional Body Repair Manuals: UPDATE
Thursday, 14 September 2023
Hyundai Motor America updated their approved body repair manuals (BRMs) available to the United States market. This includes both Hyundai and Genesis branded BRMs.
-
Structural Straightening On Tesla Vehicles: UPDATE
Wednesday, 13 September 2023
What should you do when a damaged Tesla comes into your repair facility? Can you measure it? Can it be straightened? What needs to be replaced?
-
I-CAR Repairers Realm: Ford Structural Sectioning Guidelines - Now Available
Friday, 08 September 2023
I-CAR had a discussion on Ford structural sectioning guidelines.
-
Calibration Research Tips: Honda/Acura Millimeter Wave Radar Mounting Position Inspection
Wednesday, 06 September 2023
While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by…
-
Locating ADAS Information: Maserati - UPDATE
Friday, 01 September 2023
As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern…
-
OEM-Approved Pigtail Connector Kit Resources: Nissan/INFINITI
Thursday, 31 August 2023
When confronted with a wiring harness repair, we often struggle finding the correct connector and pigtail repair kits. Often a specific connector may be used on multiple applications. If the…
-
OEM Emergency Response Guides: Toyota/Lexus - UPDATE
Wednesday, 30 August 2023
Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to…
- 2023
- September 2023 (8)
- August 2023 (12)
- July 2023 (9)
- June 2023 (12)
- May 2023 (12)
- April 2023 (11)
- March 2023 (13)
- February 2023 (10)
- January 2023 (11)
- 2022
- December 2022 (11)
- November 2022 (12)
- October 2022 (11)
- September 2022 (13)
- August 2022 (11)
- July 2022 (10)
- June 2022 (13)
- May 2022 (11)
- April 2022 (12)
- March 2022 (11)
- February 2022 (12)
- January 2022 (13)
- 2021
- December 2021 (15)
- November 2021 (12)
- October 2021 (13)
- September 2021 (15)
- August 2021 (12)
- July 2021 (16)
- June 2021 (17)
- May 2021 (14)
- April 2021 (14)
- March 2021 (21)
- February 2021 (15)
- January 2021 (14)
- 2020
- December 2020 (13)
- November 2020 (17)
- October 2020 (12)
- September 2020 (14)
- August 2020 (11)
- July 2020 (18)
- June 2020 (16)
- May 2020 (14)
- April 2020 (20)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)
- 2019
- December 2019 (13)
- November 2019 (19)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (21)
- May 2019 (19)
- April 2019 (20)
- March 2019 (21)
- February 2019 (21)
- January 2019 (18)
- 2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (21)
- July 2018 (20)
- June 2018 (21)
- May 2018 (17)
- April 2018 (19)
- March 2018 (22)
- February 2018 (17)
- January 2018 (20)
- 2017
- December 2017 (13)
- November 2017 (15)
- October 2017 (19)
- September 2017 (20)
- August 2017 (20)
- July 2017 (18)
- June 2017 (23)
- May 2017 (20)
- April 2017 (15)
- March 2017 (18)
- February 2017 (11)
- January 2017 (13)
- 2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (11)
- August 2016 (11)
- July 2016 (8)
- June 2016 (13)
- May 2016 (10)
- April 2016 (11)
- March 2016 (12)
- February 2016 (11)
- January 2016 (8)
- 2015
- December 2015 (9)
- November 2015 (8)
- October 2015 (9)
- September 2015 (7)
- August 2015 (11)
- July 2015 (10)
- June 2015 (8)
- May 2015 (8)
- April 2015 (9)
- March 2015 (8)
- February 2015 (9)
- January 2015 (11)
- 2014
- December 2014 (12)
- November 2014 (7)
- October 2014 (11)
- September 2014 (10)
- August 2014 (9)
- July 2014 (12)
- June 2014 (9)
- May 2014 (14)
- April 2014 (9)
- March 2014 (6)
- February 2014 (1)
- January 2014 (27)