Advanced Driver Assistance Systems: 2019 Honda Pilot
While many have noticed that advanced driver assistance systems (ADAS) are showing up on vehicles, there still is confusion on what is required of these systems after a collision occurs. The Ask I-CAR team frequently gets questions in regard to calibration of ADAS. Many of these questions can be answered simply by searching the OEM Calibration Requirements Search. However, there are some questions that may need more detail than the calibration search provides. Let’s take a look at the 2019 Honda Pilot ADAS.
For 2019, the Pilot comes standard equipped with collision braking, lane keep assist, and adaptive cruise control. Also available on the Pilot are blind spot detection, side view (LaneWatch), rear view, park assist, and rear cross traffic. This means that there is a large array of cameras and sensors that collision repairers will need to be aware of, many of which will require calibrations. Information for when these calibrations are required can be found in the vehicle specific repair information, and also on the 2019 Honda Pilot OEM Calibration Requirements Search page.
Starting in the front of the vehicle, is the front radar. This sensor is located behind the Honda “H” grille emblem. The sensor is mounted to the radiator core support. This radar sensor sends information to the collision braking system and the adaptive cruise control system. Calibration is required for this sensor.
Located in the interior of the vehicle, in front of the rearview mirror is the forward-facing camera. This camera sends data to the lane keep and collision braking systems. Calibration is required for this camera according to the events listed in the repair manual.
In the passenger side mirror, is a side view camera. Unique to Honda, this camera looks in the lane next to the vehicle. The camera view lets the driver see if there is a vehicle in the blind spot when changing lanes. Calibration is required for this camera.
Behind the rear bumper cover are two radar sensors. There is one on each side, attached to the outer quarter panel. These sensors are used by the blind spot detection and rear cross traffic systems. Calibration is required for these sensors.
Finally, there is a camera located in the center bezel on the rear liftgate. This camera is for the rear view system. This camera will not require calibration.
For additional Honda information, check out the Honda OEM Information page.
Additional I-CAR Collision Repair News you may find helpful:
ADAS, Calibration, And Scanning Article Hotspot
Collision Information Website Access: Honda/Acura
Honda/Acura ADAS Information Documents: UPDATE
How To Use The OEM Calibration Requirements Search
Locating ADAS Information: Honda/Acura - UPDATE
Related I-CAR Courses
-
Pre- and Post-Repair System Scanning Position Statements
Wednesday, 09 January 2019
Are you wondering if a particular OEM or organization has a published position statement on pre-repair and post-repair scanning? We have compiled a list of most of the position statements…
-
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning
Thursday, 28 July 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
-
ADAS, Calibration, And Scanning Article Hotspot
Monday, 14 January 2019
Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s…
-
Restraints Wiring Repairs
Monday, 23 May 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
-
Typical Calibration Requirements For Blind Spot Sensors
Wednesday, 19 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Honda/Acura Position Statement: Pre- and Post-Repair System Scanning - UPDATE
Wednesday, 22 May 2019
Honda /Acura have updated their position statement on pre- and post-repair scanning to give more clarification on what is expected for scanning.
-
Typical Calibration Requirements For Forward Radar Sensors
Wednesday, 12 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
MIG Brazing What Is It, Why Should I Use It?
Monday, 02 June 2014
Why MIG Brazing? It is widely known that GMA welded; fully galvanized steel will lose some of its properties, including corrosion protection, due to the heat created during welding. OEMs…
-
FCA/Stellantis Position Statement: Pre- and Post-Repair System Scanning
Thursday, 09 June 2016
FCA/Stellantis has released a position statement related to pre- and post-repair system scanning.
-
Typical Calibration Requirements For Park Assist Sensors
Monday, 31 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Genesis: Who Requires Or Recommends MIG Brazing?
Friday, 29 September 2023
In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent.…
-
OEM Linking Pin: 2018-2023 GMC Terrain Quarter Panel Sectioning Location
Wednesday, 27 September 2023
As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. Recently, we had a…
-
I-CAR Just In Time: GM Exhaust Shield Fasteners
Tuesday, 26 September 2023
Sometimes seeing is understanding, that’s why I-CAR's technical team created the Just in Time video series to guide you through a variety of collision repair topics from ADAS and EVs…
-
Back-To-Basics: Door Handle Tools
Friday, 22 September 2023
Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. Tools for the door handle might not sound exciting, but they can save you frustration…
-
OEM Emergency Response Guides: Rivian
Wednesday, 20 September 2023
Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to…
-
Locating ADAS Information: GM - UPDATE
Friday, 15 September 2023
As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern…
-
Hyundai/Genesis Releases Additional Body Repair Manuals: UPDATE
Thursday, 14 September 2023
Hyundai Motor America updated their approved body repair manuals (BRMs) available to the United States market. This includes both Hyundai and Genesis branded BRMs.
-
Structural Straightening On Tesla Vehicles: UPDATE
Wednesday, 13 September 2023
What should you do when a damaged Tesla comes into your repair facility? Can you measure it? Can it be straightened? What needs to be replaced?
-
I-CAR Repairers Realm: Ford Structural Sectioning Guidelines - Now Available
Friday, 08 September 2023
I-CAR had a discussion on Ford structural sectioning guidelines.
-
Calibration Research Tips: Honda/Acura Millimeter Wave Radar Mounting Position Inspection
Wednesday, 06 September 2023
While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by…
- 2023
- September 2023 (11)
- August 2023 (12)
- July 2023 (9)
- June 2023 (12)
- May 2023 (12)
- April 2023 (11)
- March 2023 (13)
- February 2023 (10)
- January 2023 (11)
- 2022
- December 2022 (11)
- November 2022 (12)
- October 2022 (11)
- September 2022 (13)
- August 2022 (11)
- July 2022 (10)
- June 2022 (13)
- May 2022 (11)
- April 2022 (12)
- March 2022 (11)
- February 2022 (12)
- January 2022 (13)
- 2021
- December 2021 (15)
- November 2021 (12)
- October 2021 (13)
- September 2021 (15)
- August 2021 (12)
- July 2021 (16)
- June 2021 (17)
- May 2021 (14)
- April 2021 (14)
- March 2021 (21)
- February 2021 (15)
- January 2021 (14)
- 2020
- December 2020 (13)
- November 2020 (17)
- October 2020 (12)
- September 2020 (14)
- August 2020 (11)
- July 2020 (18)
- June 2020 (16)
- May 2020 (14)
- April 2020 (20)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)
- 2019
- December 2019 (13)
- November 2019 (19)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (21)
- May 2019 (19)
- April 2019 (20)
- March 2019 (21)
- February 2019 (21)
- January 2019 (18)
- 2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (21)
- July 2018 (20)
- June 2018 (21)
- May 2018 (17)
- April 2018 (19)
- March 2018 (22)
- February 2018 (17)
- January 2018 (20)
- 2017
- December 2017 (13)
- November 2017 (15)
- October 2017 (19)
- September 2017 (20)
- August 2017 (20)
- July 2017 (18)
- June 2017 (23)
- May 2017 (20)
- April 2017 (15)
- March 2017 (18)
- February 2017 (11)
- January 2017 (13)
- 2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (11)
- August 2016 (11)
- July 2016 (8)
- June 2016 (13)
- May 2016 (10)
- April 2016 (11)
- March 2016 (12)
- February 2016 (11)
- January 2016 (8)
- 2015
- December 2015 (9)
- November 2015 (8)
- October 2015 (9)
- September 2015 (7)
- August 2015 (11)
- July 2015 (10)
- June 2015 (8)
- May 2015 (8)
- April 2015 (9)
- March 2015 (8)
- February 2015 (9)
- January 2015 (11)
- 2014
- December 2014 (12)
- November 2014 (7)
- October 2014 (11)
- September 2014 (10)
- August 2014 (9)
- July 2014 (12)
- June 2014 (9)
- May 2014 (14)
- April 2014 (9)
- March 2014 (6)
- February 2014 (1)
- January 2014 (27)
