Advanced Driver Assistance Systems: 2019 Toyota Camry

While many have noticed that advanced driver assistance systems (ADAS), are showing up on vehicles. There still is confusion on what is required of these systems after a collision occurs. The Ask I-CAR team frequently get questions in regard to calibration of ADAS. Many of these questions can be answered simply by searching the OEM Calibration Requirements Search. However, there are some questions that may need more details than the calibration search provides. Let’s take a look at the 2019 Toyota Camry ADAS.
If you get a 2019 Camry in your repair stall, you can be guaranteed that it will have ADAS equipped. For 2019, all trims of the Camry are fitted with rear view, collision warning, collision braking, lane departure warning, lane keep assist, adaptive lighting, and adaptive cruise control. As optional equipment there is a 360° camera view, blind spot detection, park assist, and rear cross traffic. This means that there is a large array of cameras and sensors that collision repairers will need to be aware of, many of which will require calibrations. Information for when these calibrations are required can be found in the vehicle specific repair information and also on the 2019 Toyota Camry OEM Calibration Requirements Search page.
Starting at the front of the vehicle, there are four ultrasonic sensors that collect data for the park assist system. In addition, there are another four ultrasonic sensors located in the rear bumper cover. These sensors are spaced out from one side of the bumper to the other. Calibration is required for this suite of sensors depending on different events.
Located just below the Toyota emblem in the grille is the front camera that is part of the 360° camera view system. This four-camera system has another camera located on the bottom of each exterior side mirror, looking down. A final camera is located on the trunk lid below the Toyota emblem, above the license plate. There are several events that will make calibration necessary for these cameras.
Attached to the backside of the front Toyota Emblem in the grille, is the front radar sensor. There are several events that will make calibration necessary for this sensor.
The forward-facing camera is located inside the vehicle at the top center of the windshield in front of the rearview mirror. Toyota states that the camera lens should never be touched and should replaced if it is. Other reasons for replacement include if the camera is struck, dropped, or has any foreign matter on it. If the camera bracket is damage it too must be replaced along with the windshield.
Behind the rear bumper cover bolted to the outer quarter panel there is a blind spot radar sensor on each side below the tail lamp. Toyota warns that the sensor should be replaced if it is subjected to any impact. Calibration for these sensors is required when certain events take place.
This is just a brief overview of some of the different required procedures for the 2019 Toyota Camry. Always consult the OEM repair information to get the exact information and procedures required to service the ADAS.
For additional Toyota information, check out the Toyota OEM Information page.
Additional I-CAR Collision Repair News you may find helpful:
ADAS, Calibration, And Scanning Article Hotspot
Collision Information Website Access: Toyota/Lexus/Scion
How To Use The OEM Calibration Requirements Search
Locating ADAS Information: Toyota/Lexus
Related I-CAR Courses
-
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning
July 28, 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
-
MIG Brazing What Is It, Why Should I Use It?
June 02, 2014
Why MIG Brazing? It is widely known that GMA (MIG) welded; fully galvanized steel will lose some of its properties, including corrosion protection, due to the heat created during welding.…
-
Pre- and Post-Repair System Scanning Position Statements
January 09, 2019
Are you wondering if a particular OEM or organization has a published position statement on pre-repair and post-repair scanning? We have compiled a list of most of the position statements…
-
Typical Calibration Requirements for Blind Spot Sensors
October 19, 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Restraints Wiring Repairs
May 23, 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
-
OEM Linking Pin: 2015 Ford F-150 Outer Box Side Replacement Options - UPDATE
August 07, 2015
The method for replacing the outer box side on the 2015 Ford F-150 has been a popular area of discussion, and many people are asking, "What are my options and…
-
Typical Calibration Requirements for Forward Radar Sensors
October 12, 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Typical Calibration Requirements for Park Assist Sensors
October 31, 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Mazda I-ELOOP Overview
January 27, 2014
Beginning model year 2014, Mazda has introduced a regenerative engine braking system called i-ELOOP, short for "Intelligent Energy Loop." In this system, a capacitor is used to store electrical energy…
-
I-CAR Best Practice: Recycled Outer Quarter Panels w/Rolled Hem Flanges
July 21, 2017
Periodically, I-CAR Repairability Summits are held to bring together collision industry stakeholders and subject matter experts to develop collision repair processes and best practices for repair of late-model, collision damaged…
-
Toyota Collision Pros: 2021 Issue 1
March 04, 2021
Toyota has released the latest edition of their Collision Pros magazine. This issue highlights the all-new 2021 Toyota Sienna and focuses on the technology aspects of the vehicle.
-
OEM Emergency Response Guides: Nissan/INFINITI
March 03, 2021
Are you looking for OEM emergency response guides (ERGs)? The RTS team has located these guides and either houses them on the RTS website, provides links to webpages that house…
-
Toyota/Lexus: Who Requires Or Recommends MIG Brazing
March 02, 2021
In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent.…
-
Spot And Plug Weld Nugget Size: Mitsubishi
February 26, 2021
Did you know that many OEMs specify nugget size for spot and plug welds? This information is typically found within vehicle-specific repair procedures or can be found under general welding…
-
Audi Emergency Response Guides Now Available On RTS Portal
February 25, 2021
Audi emergency response guides (ERGs) can now be accessed directly from the Repairability Technical Support (RTS) Portal on the Audi OEM Information page. These guides provide information about the vehicle…
-
OEM Emergency Response Guides
February 25, 2021
Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to…
-
I-CAR RTS Airbag And Restraints System Technology Webinar
February 24, 2021
I-CAR RTS has created a webinar on supplemental restraints systems (SRS). The webinar is a comprehensive look at vehicle SRS systems, how they work, and details and cautions that are…
-
Repairer Driven News: BMW Incorrect Windshield Use
February 19, 2021
Repairer Driven News (RDN) released an article on BMW vehicles and a few things to consider when repairing them. The article covers two main areas of concern.
-
Rolls-Royce: Who Requires Or Recommends MIG Brazing?
February 17, 2021
In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent.…
-
BMW/Mini: Who Requires Or Recommends MIG Brazing?
February 17, 2021
In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent.…
- 2021
- March 2021 (3)
- February 2021 (15)
- January 2021 (14)
- 2020
- December 2020 (15)
- November 2020 (17)
- October 2020 (14)
- September 2020 (14)
- August 2020 (12)
- July 2020 (19)
- June 2020 (16)
- May 2020 (14)
- April 2020 (21)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)
- 2019
- December 2019 (15)
- November 2019 (20)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (21)
- May 2019 (20)
- April 2019 (21)
- March 2019 (21)
- February 2019 (21)
- January 2019 (18)
- 2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (23)
- July 2018 (21)
- June 2018 (21)
- May 2018 (19)
- April 2018 (20)
- March 2018 (23)
- February 2018 (17)
- January 2018 (21)
- 2017
- December 2017 (16)
- November 2017 (18)
- October 2017 (19)
- September 2017 (20)
- August 2017 (21)
- July 2017 (19)
- June 2017 (23)
- May 2017 (21)
- April 2017 (15)
- March 2017 (20)
- February 2017 (12)
- January 2017 (13)
- 2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (11)
- August 2016 (11)
- July 2016 (8)
- June 2016 (13)
- May 2016 (11)
- April 2016 (12)
- March 2016 (14)
- February 2016 (11)
- January 2016 (7)
- 2015
- December 2015 (10)
- November 2015 (10)
- October 2015 (12)
- September 2015 (10)
- August 2015 (12)
- July 2015 (11)
- June 2015 (10)
- May 2015 (8)
- April 2015 (10)
- March 2015 (9)
- February 2015 (11)
- January 2015 (12)
- 2014
- December 2014 (15)
- November 2014 (9)
- October 2014 (12)
- September 2014 (10)
- August 2014 (11)
- July 2014 (13)
- June 2014 (9)
- May 2014 (14)
- April 2014 (9)
- March 2014 (6)
- February 2014 (1)
- January 2014 (28)