Collision Hub - Repair University Live: Scanning vs. Calibration

Posted on 18 May 2017

Collision Hub is a well-known source for collision repair news and information. On the Collision Hub website, you can find a monthly news report (Collision Hub Network News - CHNN), a blog, Repair University, and a relatively new feature Repair University Live. To view Repair University Live, you will need to purchase a subscription. However, the next episode, coming up on May 24, at 12:00 PM Eastern, will be sponsored by Mitchell, so it will be free to the public. Let’s take a look at how to view this episode and what it will include.

Continue Reading...

New Calibration Requirement From General Motors

Posted on 18 May 2017

There is new information available when it comes to windshield replacement on General Motors (GM) vehicles. In the past, forward facing camera calibration was not required when replacing the windshield. Let’s take a look at the new requirement from GM.

Continue Reading...

Additional Calibration Requirements: Volkswagen

Posted on 16 May 2017

The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.

Continue Reading...

Structural Sectioning Procedures: Nissan/INFINITI

Posted on 15 May 2017

Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.

Continue Reading...

OEM Position Statements

Posted on 12 May 2017

Here at Ask I-CAR we get a lot of questions on a daily basis. Many of these questions have to do with what the OEM says on a particular subject. Often times, these questions can be quickly answered by an OEM position statement. Let’s find out how OEM position statements can help you.

Continue Reading...

Additional Calibration Requirements: FCA/Stellantis

Posted on 11 May 2017

The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.

Continue Reading...

What's That in the Grille?

Posted on 11 May 2017

Have you noticed anything different looking on new vehicle grilles? If you have, you may have thought what is that strange looking flat spot? Sometimes this flat area is somewhat hidden by a manufacturer emblem. Other times it’s integrated into the grille itself, including grille lines. Let’s take a look at this new design element and what it’s hiding.

Continue Reading...

Additional Calibration Requirements: General Motors

Posted on 05 May 2017

The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. The OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.

Continue Reading...

Identifying Options for Windshields

Posted on 04 May 2017

Automotive windshields have changed a lot since the start of the automotive industry. In the past, there were some variations in windshields, but nothing like todays windshields. One particular model of vehicle can have dozens of different options when it comes to ordering a windshield. Let’s take a look at some of these options, and how to identify them.

Continue Reading...

Structural Sectioning Procedures: Kia

Posted on 03 May 2017

Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.

Continue Reading...

Weld-Through Primer Guidelines: INFINITI

Posted on 01 May 2017

Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what INFINITI recommends and where this information can be found.

Continue Reading...

Additional Calibration Requirements: Kia

Posted on 28 April 2017

The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.

Continue Reading...

Structural Sectioning Procedures: Mazda

Posted on 27 April 2017

Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.

Parts are made from various materials including HSS, UHSS, aluminum, and carbon fiber. These parts also have complex designs to collapse or transfer collision forces in a specific manner. Introducing a sectioning joint to many of these parts will alter how the part reacts to those collision forces. For this reason, sectioning a part is only allowed if supported by vehicle maker repair information. Let’s see what Mazda says about structural sectioning.

Continue Reading...

Weld-Through Primer Guidelines: Porsche

Posted on 24 April 2017

Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Porsche recommends and where this information can be found.

Continue Reading...

Weld-Through Primer Guidelines

Posted on 21 April 2017

Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what we have found for weld-through primer guidelines.

Continue Reading...