What Happened To The I-CAR Advantage Articles?

Posted on 06 October 2022

What happened to the I-CAR Advantage articles?

Continue Reading...

I-CAR Repairers Realm: I-CAR Chicago Technical Center (CTC) Shop Overview - Now Available

Posted on 05 October 2022

I-CAR had a discussion on the I-CAR Chicago Technical Center (CTC).

Continue Reading...

Weld-Through Primer Guidelines: Genesis

Posted on 30 September 2022

Weld-through primers are generally a zinc-based product that is applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide, which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Genesis recommends and where this information can be found.

Continue Reading...

Refinishing Park Assist Sensors: Volvo

Posted on 29 September 2022

Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require painting to match the vehicle. Vehicle makers often provide information on the painting of new sensors. Some vehicle makers do not recommend refinishing sensors with minor finish damage because excessive paint thickness may adversely affect the operation of the park assist system. However, other vehicle makers allow refinishing and provide guidelines. Let’s see what Volvo has to say.

Continue Reading...

Maserati Restraints Wiring

Posted on 29 September 2022

The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Maserati’s position on this subject.

Continue Reading...

Corrosion Protection Guidelines: Hyundai

Posted on 23 September 2022

A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots, that left untreated will lead to corrosion, and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let’s take a look at what Hyundai says.

Continue Reading...

Advanced Driver Assistance Systems: 2021 Nissan Rogue

Posted on 22 September 2022

While many have noticed that advanced driver assistance systems (ADAS) are showing up on vehicles, there still is confusion on what is required of these systems after a collision occurs. The Ask I-CAR team frequently gets questions in regard to calibration of ADAS. Many of these questions can be answered simply by searching the OEM Calibration Requirements Search. However, there are some questions that may need more details than the calibration search provides. Let’s take a look at the 2021 Nissan Rogue ADAS.

Continue Reading...

Structural Sectioning Procedures: Tesla

Posted on 21 September 2022

Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.

Continue Reading...

One-Time-Use Parts And Fasteners: Kia

Posted on 16 September 2022

What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information?"

Continue Reading...

Additional Calibration Requirements: Genesis

Posted on 15 September 2022

The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.

It does not include Occupant Classification Systems (OCS), steering angle sensors, battery disconnects, or other calibrations/initializations required, when not related directly to ADAS. Let’s take a look at what additional items may require calibrations/initializations on Genesis vehicles.

Continue Reading...

I-CAR Static ADAS Calibration 3-Day Hands-On Skills Development Course

Posted on 09 September 2022

I-CAR has developed a hands-on course that will improve the knowledge base of learners regarding static calibrations on advanced driver assistance systems (ADAS). During the course, the learner will also gain experience with multiple vehicles and different systems.

Continue Reading...

I-CAR Repairers Realm: Ford F-150 Outer Box Panel Replacement - Now Available

Posted on 08 September 2022

I-CAR had a discussion with industry experts on replacing an F-150 outer box side.

Continue Reading...

Locating OEM-Approved HV Tools: Nissan/INFINITI

Posted on 07 September 2022

When researching procedures for disabling a high-voltage (HV) vehicle, you may notice that many of the procedures require the use of specific tools. Some of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.

Continue Reading...

Weld-Through Primer Guidelines: Rolls-Royce

Posted on 02 September 2022

Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Rolls-Royce recommends and where this information can be found.

Continue Reading...

Jaguar Land Rover High-Voltage Technician Levels

Posted on 01 September 2022

As electric-only, hybrid, and fuel cell electric vehicles are increasing in sales, they are becoming more commonplace in repair facilities. Along with the unique powertrains that come with these vehicles, also comes unique safety concerns. Regardless of vehicle maker, high-voltage (HV) systems pose a threat of injury or death if not handled properly. Only personnel with the proper training, PPE, tools, equipment, and service information should perform work on the HV systems.

Continue Reading...