Did you know that in 2013, General Motors published a position statement that identifies that sectioning should only be performed in recommended areas? This warning is applicable to all GM lines including Buick, Cadillac, Chevrolet, and GMC.
Vehicle makers each have their own way of organizing their repair information. The names of the materials and even the names of different parts of vehicles may vary.
When determining repair vs. replace options for damaged cab-mounting areas, determine if the vehicle maker providesa service part and written replacement procedures. If there is no replacement procedure, but the service part is available, duplicate the original factory attachment method. If the part is not available as a separate service part, replacement of a major part of the frame, or the entire frame, may be the only option (See Figure 1).
Subaru has been growing in market share over the past few years. With more and more Subarus on the road everyday, what is the collision repair industry going to do about repairing these vehicles that are being seen with more regularity?
The roof panel on the 2013 Nissan 370Z is laser-welded along the roof-to-side panel mating flange from the factory. Through a routine technical inquiry from a collision repair facility, the I-CAR Repairability Technical Support team was asked if a Nissan procedure existed for replacing the roof panel.
As part of the I-CAR Repairability Technical Support (RTS) initiative's OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. Recently we had a technical inquiry that asked, "Do you have to replace a front passenger airbag on a Subaru even if only the driver's airbag deployed? The repair information seems to indicate that it should."
Carbon fiber is being used on many late-model vehicles and has become a buzzword in the industry. This article answers some questions you may have been wondering about on the use and repair of carbon fiber.
Beginning model year 2014, Mazda has introduced a regenerative engine braking system called i-ELOOP, short for "Intelligent Energy Loop." In this system, a capacitor is used to store electrical energy generated during deceleration. In a conventional system when the vehicle slows or stops, energy is wasted. The i-ELOOP system uses a unique variable voltage alternator that can produce up to 25 volts during deceleration. The electricity that is generated during deceleration is not sent directly to the vehicle's battery, because the battery cannot store more than 12 volts. Instead, the capacitor stores the electricity, up to the 25 volts produced by the alternator. The capacitor then readily discharges it through a voltage reduction circuit to power vehicle accessories.
Kia Motors has released a comprehensive collision repair manual for the Kia Soul, in the United States!
by Jason Bartanen
We've seen a lot of changes in vehicle technology over the years. With each of these changes come new challenges and new opportunities. When the unibody vehicle was introduced, repair professionals were required to change their approach to collision repair, from damage analysis through the repair process. With the introduction of GMA (MIG) welding, additional requirements for repairs included new training and equipment. And passive restraints systems presented a completely different type of challenge, involving electronics and diagnostics.
To help the industry be better prepared for repairing new vehicles, I-CAR has updated the Training and Certification: Steel Sectioning. With the changes to vehicles happening daily from new materials, thinner materials, new technologies, and new repair procedures, collision repair technicians have had to update their skills to repair the new vehicles.
A new free publication from Honda features body repair information on their new models. The first two editions of Body Repair News are now available on Honda's Service Express website. The premier publication in the series focuses on new model body repair information for the 2014 Acura MDX and the second edition covers the 2013 Honda Accord. Subsequent Body Repair News editions will be created, or updated, for each new model and any minor model change where significant body design changes are made.
If you haven't been exposed to MIG brazing yet, it's likely that you will be in the not-too-distant future. More and more popular vehicles are requiring MIG brazing for attaching certain high-strength steel (HSS) parts when making collision repairs. An example of this is on the 2013 Honda Accord.
The Occupational Safety and Health Administration (OSHA) is requiring that all employees be trained, by December 1st of 2013, on the revision to its Hazard Communication Standard. The revision to the 1994 standard more closely aligns with the Globally Harmonized System (GHS), an international approach to labeling and classifying hazardous products.
If there is a sectioning procedure on a front lower rail, GMA welding across a seam is the usual method for attaching the new joint. On at least two late model Porsche vehicles, however, there is a front lower rail sectioning procedure that uses no welds at all. The rails on the Panamera, since 2010, and the 911, since 2012, both have aluminum construction.
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
Are you wondering if a particular OEM or organization has a published statement on pre-repair and post-repair scanning? We have compiled a list of most of the statements on the subject, so you can...
Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on...
Honda /Acura has updated their position statement on pre- and post-repair scanning to give more clarification on what is expected for scanning.
BMW has released a position statement related to pre- and post-repair system scanning. The statement applies to All vehicles equipped with on board diagnostics II (OBD II).
The I-CAR best practice article, Recycled Outer Quarter Panels w/Rolled Hem Flanges has gotten a lot of interest from the collision repair industry. It’s important to know which vehicles are...
As the industry continues to ask, are pre- and post-repair scans necessary, General Motors provides their answer.
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
FCA/Stellantis has released a position statement related to pre- and post-repair system scanning.
Nissan/INFINITI updated their position statement on pre- and post-repair scanning. The revised position statement touches on more subjects and gives additional information on the subject.
Repairer Driven News (RDN) released an article featuring an updated Rivian procedure.
I-CAR had a discussion on KECO tools for lateral tension dent removal.
Sometimes seeing is understanding, that’s why I-CAR's technical team created the Just in Time video series to guide you through a variety of collision repair topics from ADAS and EVs to repair tips...
Per your requests, here are the step-by-step instructions for submitting a library request in ALLDATA.
Sometimes, going back to the basics can make the difference between a quality repair and a failed repair. When researching some OEM body repair manuals (BRMs), you may find callouts for the use of...
Sometimes seeing is understanding, that’s why I-CAR's technical team created the Just in Time video series to guide you through a variety of collision repair topics from ADAS and EVs to repair tips...
I-CAR held a repairability summit on supplemental restraints systems (SRS) inspections. In attendance were representatives from OEMs, information providers, collision repair facilities, and insurers.
Sometimes seeing is understanding, that’s why I-CAR's technical team created the Just in Time video series to guide you through a variety of collision repair topics from ADAS and EVs to repair tips...
While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by...
Sometimes, going back to the basics can make the difference between a quality repair and a failed repair. Rivets and rivet bonding are common attachment methods on today’s vehicles. Although rivet...
