Jaguar News
Jaguar Land Rover Mechanical, Electrical, And Trim (MET) Training
Posted on 31 October 2025I-CAR now provides mechanical, electrical, and trim (MET) training for Jaguar Land Rover (JLR). This training is a new requirement for Jaguar Land Rover Authorized Collision Repair Centers.
Jaguar Land Rover Restraints Wiring: UPDATE
Posted on 14 August 2025The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Jaguar Land Rover's position on this subject.
OEM-Approved Connector And Pigtail Repair Resources: Jaguar Land Rover
Posted on 1 August 2025When confronted with a wiring harness repair, we often struggle to find the correct connector and pigtail repair kits. Often, a specific connector may be used on multiple applications. If the connector is allowed to be replaced, what resources are available to locate approved wiring connectors and pigtail repair kits? Let’s see what Jaguar Land Rover has to offer.
Structural Straightening On Jaguar Land Rover Vehicles
Posted on 7 February 2025What should you do when a damaged Jaguar Land Rover comes into your repair facility? Can it be straightened? What is a structural part? What type of equipment is required?
I-CAR OEM Technical Information Matrix: What Is It, And How Does It Help? UPDATE
Posted on 5 December 2024Do you know which vehicle makers have collision repair information available? Do you know where you can go to find that out?
Refinishing Park Assist Sensors: Jaguar Land Rover
Posted on 22 October 2024Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require painting to match the vehicle. Vehicle makers often provide information on the painting of new sensors. Some vehicle makers do not recommend refinishing sensors with minor finish damage because excessive paint thickness may adversely affect the operation of the park assist system. However, other vehicle makers allow refinishing and provide guidelines. Let’s see what Jaguar Land Rover (JLR) has to say.
Bumper Cover Repair With ADAS: Jaguar Land Rover - UPDATE
Posted on 13 June 2024A simple bumper repair on a modern vehicle may not be as simple as it seems. New technologies like blind spot monitoring, adaptive cruise control, and other advanced driver assistance systems (ADAS) utilize sensors behind the bumper covers. The ability for these sensors to be able to see clearly, normally requires special caution when considering a bumper repair. Many OEMs have different levels of warnings when it comes to repairing bumper covers with ADAS. So, what does Jaguar Land Rover say on the subject?
High-Voltage Vehicle Paint Booth Quick Reference
Posted on 9 April 2024When refinishing high-voltage (HV) vehicles, it is important to check for OEM paint booth temperature recommendations so that HV components do not get damaged in the heat.
OEM Emergency Response Guides: Jaguar Land Rover - UPDATE
Posted on 26 January 2024Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Locating OEM-Approved HV Tools: Jaguar Land Rover
Posted on 6 April 2023When researching procedures for disabling a high-voltage (HV) vehicle, you may notice that many of the procedures require the use of specific tools. Some of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.
Body Construction And Material Repair Guidelines: Jaguar Land Rover
Posted on 17 November 2022What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
As we know, today’s vehicles can be constructed from a wide variety of materials. Knowing if the OEM provides information on body construction materials and repair guidelines is a crucial step in providing a complete, safe, and quality repair. Let’s see what Jaguar Land Rover has to say.
Jaguar Land Rover High-Voltage Technician Levels
Posted on 1 September 2022As electric-only, hybrid, and fuel cell electric vehicles are increasing in sales, they are becoming more commonplace in repair facilities. Along with the unique powertrains that come with these vehicles, also comes unique safety concerns. Regardless of vehicle maker, high-voltage (HV) systems pose a threat of injury or death if not handled properly. Only personnel with the proper training, PPE, tools, equipment, and service information should perform work on the HV systems.
Non-SRS Wiring Repairs: Jaguar Land Rover
Posted on 17 June 2022What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As technology increases on vehicles, so does the number of components that utilize electricity. Many of the sensors and modules are becoming smarter and more sensitive. If the wire is too long, the wrong gauge, or spliced in the wrong location, it can cause malfunctions in the components that it’s powering. Many OEMs have different restrictions and guidelines for repairing wiring that does not control SRS components. On the other hand, there are OEMs that don’t allow wiring repairs at all, so full harness replacement is the only option.
One-Time-Use Parts And Fasteners: Jaguar Land Rover
Posted on 18 May 2022What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information?"
Identifying The Correct Body Repair Manual: Jaguar Land Rover
Posted on 28 April 2022Vehicle makers may group their body repair manuals (BRM) in several different ways. Sometimes the BRMs are grouped by a year range, some are listed as VIN specific, and others are arranged by a body code. Let’s take a look at Jaguar Land Rover to see how they group their BRMs.
Where Do I Find Other Types Of Information In Jaguar Land Rover?
Posted on 28 December 2021Navigating OEM websites can be challenging when searching for collision repair procedures, especially as no two OEM websites are alike. What happens when you need to find other types of repair information, such as, "What needs to be inspected after a supplemental restraint system (SRS) deployment?", or "Does the tire pressure monitoring system (TPMS) require a scan tool or specialty tool?" Let's take a closer look at the Jaguar Land Rover website.
Rivet Guns: Does My Shop Need Them?
Posted on 23 July 2021When performing collision repairs, there are more attachment methods available than ever before. OEMs specify which attachment methods are recommended or required. If a method is not listed as an option, it should not be used.
Jaguar Land Rover: Who Requires Or Recommends MIG Brazing?
Posted on 13 April 2021In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S. Let’s see what Jaguar Land Rover (JLR) has to say.
OEM Emergency Response Guides
Posted on 25 February 2021Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Repairer Driven News: Jaguar Land Rover Structural Composite Study
Posted on 27 January 2021Repairer Driven News (RDN) released an article on the Jaguar Land Rover (JLR) four-year research project that focuses on electric vehicles (EVs) and using composites to make lighter vehicles.
Sectioning And Partial Part Replacement: 2020 Land Rover Defender
Posted on 23 December 2020One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2020 Land Rover Defender.
Who Requires Or Recommends MIG Brazing? UPDATE
Posted on 25 November 2020In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S.
Locating ADAS Information: Jaguar Land Rover
Posted on 23 July 2020As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern vehicles. You may be required to look in numerous manuals to find the information required to safely repair the vehicle.
Repairer Driven News: 2020 Land Rover Defender
Posted on 27 September 2019Repairer driven news (RDN) released an article on the changes to the 2020 Land Rover Defender. This Defender is no longer a body over frame design. In fact, the structure of this vehicle is unlike any other Land Rover model with its own new platform. The “purpose-engineered” D7x platform was built to be the stiffest structure Land Rover has ever made. The body of this vehicle is aluminum intensive and lightweight.
Sectioning and Partial Part Replacement: 2019 Jaguar I-Pace
Posted on 18 September 2019One of the top technical inquires received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2019 Jaguar I-Pace.
How to Access Jaguar Land Rover Position Statements
Posted on 1 March 2019Jaguar Land Rover (JLR) position statements are only accessible through the Jaguar Land Rover service information site, TOPIx. From there, position statements can be accessed by Jaguar Land Rover network collision shops or by signing up for a free account. It is important to note that a free account does not provide access to the Workshop manuals.
ADAS, Calibration, And Scanning Article Hotspot
Posted on 14 January 2019Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s Repairability Technical Support (RTS) team continues to be on the leading edge of research and education. Our goal is to help communicate information to the industry, and a great way to do this is through Collision Repair News articles.
Jaguar Land Rover Position Statements Available
Posted on 7 January 2019There's a new addition to the OEM Information page for Jaguar Land Rover. An icon has been added that will link you to a page containing collision repair position statements.
Jaguar Land Rover Position Statement: Pre- and Post-Repair System Scanning
Posted on 2 January 2019As with many other OEMs, Jaguar Land Rover (JLR) has a published position statement available on pre- and post-repair scanning. Jaguar Land Rover credits advancements in technology with the need for scanning.
Corrosion Protection Guidelines: Jaguar Land Rover
Posted on 10 August 2017A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots that left untreated will lead to corrosion and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let’s take a look at what Jaguar Land Rover (JLR) says.
Additional Calibration Requirements: Jaguar Land Rover
Posted on 14 July 2017The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. The OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.
Structural Sectioning Procedures: Jaguar Land Rover
Posted on 23 June 2017Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.
Weld-Through Primer Guidelines: Jaguar Land Rover
Posted on 31 January 2017Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Jaguar Land Rover (JLR) recommends and where this information can be found.
Jaguar Land Rover Glass Replacement Requirements
Posted on 3 November 2016The role of the windshield is a lot more complex than simply allowing a view of the road ahead. It is considered a structural part of the vehicle as it contributes to the strength of the roof and A-pillars. The windshield helps to manage collision energy and has become an integral part of several advanced safety systems.
Always Follow Vehicle Maker Procedures
Posted on 7 July 2016We often receive Ask I-CAR inquiries asking: “what does I-CAR recommend?” Many times these questions are in regards to sectioning, straightening, or part replacement/attachment methods. Our first response is always:
Restraints Wiring Repairs
Posted on 23 May 2016Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
What's A Land Rover Fender Apron Panel?
Posted on 3 March 2016When it comes to repair information, vehicle makers use a wide variety of terminology for replacement parts. All of the different names can be confusing, especially when repairing a variety of vehicle makes and models.
What Is the Vehicle of the Future Made Of?
Posted on 23 September 2015The question is often asked, what material will be used in the car of the future? Should we concentrate on learning how to repair steel, aluminum, magnesium, or carbon fiber? For that answer, we need to look at present-day vehicles for some clues.
Step-By-Step: Accessing Jaguar Repair Information
Posted on 27 April 2015Per your requests, we are adding step-by-step instructions on how to access the vehicle maker repair information to complement our how-to-videos on the OEM Information pages. Easily reference this article by clicking the link under the video on the Jaguar OEM Information page.
Today’s Advanced Vehicles Require Changes in Collision Repair Attachment Methods - Part 1
Posted on 20 December 2014This article originally appeared in the November/December edition of Fixed Ops Magazine.
Collision repair professionals are no different than any other professional – we are resistant to change. It took many years for repairers to make the switch to “MIG welding” for welding early unibody vehicles. (For this article we’ll use the term gas metal arc welding (GMAW) metal inert gas (MIG), or GMA (MIG)). (More on the reason, later.) It was a technology that was unfamiliar to many and there wasn’t a perceived need for change. History would prove otherwise, as there may not be a collision repair business in the country that doesn’t have a GMA (MIG) welder.
Repair or Replace? – Material Tensile Strength Key to Repairability
Posted on 23 September 2014Repair or Replace? – Material Tensile Strength Key to Repairability
Jason Bartanen, I-CAR Director, Industry Technical Relations
The world of steels continues to evolve at a rapid pace and repair professionals need to keep up. In order to perform complete, safe, and quality repairs, it’s imperative to identify the type of material we’re working with, to know what is repairable, and know which options we have for part replacement when straightening is not an option.
Weld-Through Primer Requirements On The OEM Technical Information Matrix
Posted on 28 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The eighth column calls out if the vehicle maker requires the use of weld-through primer on flanges in preparation for welding.
Collision Repair Attachment Methods, Description, And Equipment Requirements Information On The OEM Technical Information Matrix
Posted on 13 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The seventh column calls out if the vehicle maker has information in regard to the recommended attachment method and the equipment required for complete, quality, and safe repairs.
It's Not Just About Aluminum
Posted on 30 July 2014Today's Vehicles Require Updated Collision Repair Tools And Training
by Jason Bartanen
Ever since the unveiling of the 2015 Ford F-150 at the North American International Auto Show in Detroit in January, the U.S. automotive industry has been buzzing about this game changing, aluminum intensive vehicle.
What's A Jaguar Fender Apron Panel?
Posted on 17 July 2014When it comes to repair information, vehicle makers use a wide variety of terminology for replacement parts. All of the different names can be confusing, especially when repairing a variety of vehicle makes and models.
Is There a Procedure for Disassembling a Service Assembly?
Posted on 19 June 2014The fourth column in the OEM Technical Information Matrix: Partial Service Part/Assembly Replacement Procedures at Factory Seams, can get a little tricky without further clarification. For the most part, this is a column that I-CAR is still researching published OEM information to get the answers to. The question is: Does the vehicle maker have procedures for replacing a partial service part or assembly at factory seams?
The Aluminum Difference
Posted on 9 December 2013What's Iowa Got To Do With It?
by Jason Bartanen
We've seen a lot of changes in vehicle technology over the years. With each of these changes come new challenges and new opportunities. When the unibody vehicle was introduced, repair professionals were required to change their approach to collision repair, from damage analysis through the repair process. With the introduction of GMA (MIG) welding, additional requirements for repairs included new training and equipment. And passive restraints systems presented a completely different type of challenge, involving electronics and diagnostics.
Jeep News
Spray-In Bedliner Repair Considerations
Posted on 5 June 2026We are often asked, “Can a spray-in bedliner be repaired?” Let’s take a look at some repair options and considerations.
Repairers Realm: FCA/Stellantis Corrosion Protection Updates - Now Available
Posted on 25 March 2026I-CAR discussed aluminum corrosion protection with FCA/Stellantis.
Bumper Cover Repair With ADAS: FCA/Stellantis
Posted on 25 February 2026A simple bumper repair on a modern vehicle may not be as simple as it seems. New technologies like blind spot monitoring, adaptive cruise control, and other advanced driver assistance systems (ADAS) utilize sensors behind the bumper covers. The ability for these sensors to be able to see clearly normally requires special caution when considering a bumper repair. Many OEMs have different levels of warnings when it comes to repairing bumper covers with ADAS. So, what does FCA/Stellantis say on the subject?
SEMA 2025: FCA/Stellantis Advanced Service Updates 2025
Posted on 19 November 2025I-CAR had numerous presentations at the 2025 SEMA show. One of these presentations focuses on FCA/Stellantis repair information.
Day One: I-CAR Live From The 2025 SEMA Show
Posted on 5 November 2025Day one of the numerous I-CAR and SCRS interviews and presentations at the 2025 SEMA Show.
Digital Key Considerations: FCA/Stellantis
Posted on 24 September 2025The intermingling of technology and automobiles continues, with digital key offerings from most vehicle makers. Digital keys utilize smartphone technology to expand vehicle access and owner convenience. How does this affect repairs? Let’s take a look at what FCA/Stellantis has to say.
App-Based Connected Services Considerations: FCA/Stellantis
Posted on 24 September 2025Have you had an experience where the vehicle notified the owner that it was being moved while it was in your repair facility? App-based connected services are available from many vehicle makers and may require special considerations before beginning repairs. Let’s see what FCA/Stellantis has to say.
Weld-Through Primer Guidelines: FCA/Stellantis - UPDATE
Posted on 22 January 2025Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what FCA/Stellantis recommends and where this information can be found.
I-CAR OEM Technical Information Matrix: What Is It, And How Does It Help? UPDATE
Posted on 5 December 2024Do you know which vehicle makers have collision repair information available? Do you know where you can go to find that out?
Day One: I-CAR Live From The 2024 SEMA Show
Posted on 6 November 2024Day one of the numerous I-CAR and SCRS interviews and presentations at the 2024 SEMA Show.
I-CAR Repairers Realm: Variations In OEM Service Parts - Now Available
Posted on 6 August 2024I-CAR had a discussion on variations in OEM service parts.
High-Voltage Vehicle Paint Booth Quick Reference
Posted on 9 April 2024When refinishing high-voltage (HV) vehicles, it is important to check for OEM paint booth temperature recommendations so that HV components do not get damaged in the heat.
I-CAR Repairers Realm: RAM ProMaster Hinge Pillar Repair - Now Available
Posted on 1 February 2024I-CAR had a discussion on RAM ProMaster hinge pillar repair.
I-CAR Repairers Realm: SEMA: Vehicle-Maker Required Tools and Equipment - Now Available
Posted on 6 December 2023I-CAR had a discussion on vehicle-maker required tools and equipment.
OEM-Approved Connector and Pigtail Repair Resources: FCA/Stellantis
Posted on 23 June 2023When confronted with a wiring harness repair, we often struggle finding the correct connector and pigtail repair kits. Often a specific connector may be used on multiple applications. If the connector is allowed to be replaced, what resources are available to locate approved wiring connector and pigtail repair kits? Let’s see what is available from FCA/Stellantis.
FCA/Stellantis Restraints Wiring: UPDATE
Posted on 8 June 2023The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at the FCA/Stellantis position on this subject.
Straightening And Heat: FCA/Stellantis - UPDATE
Posted on 11 May 2023FCA/Stellantis has updated the position statement that provides the requirements for the use of heat when straightening.
Body Construction And Material Repair Guidelines: FCA/Stellantis - UPDATE
Posted on 11 May 2023What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
OEM Emergency Response Guides: FCA/Stellantis
Posted on 23 February 2023Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
These guides provide information about the vehicle that is useful to emergency response personnel. You may find ERGs available for many types of vehicles, but most OEMs focus on how to handle a high-voltage (HV) vehicle that has been involved in a collision.
FCA/Stellantis: Bumper Cover Removal With Active Air Dams
Posted on 7 October 2022Some FCA/Stellantis vehicles use active air dams underneath the front bumper cover to improve the aerodynamics of the vehicle. With active air dams, comes some considerations when removing and installing a front bumper cover. Let’s take a look at what FCA/Stellantis has to say.
FCA/Stellantis High-Voltage Technician Levels
Posted on 19 August 2022As electric-only, hybrid, and fuel cell electric vehicles are increasing in sales, they are becoming more commonplace in repair facilities. Along with the unique powertrains that come with these vehicles, also comes unique safety concerns. Regardless of vehicle maker, high-voltage (HV) systems pose a threat of injury or death if not handled properly. Only personnel with the proper training, PPE, tools, equipment, and service information should perform work on the HV systems.
I-CAR Wagoneer And Grand Wagoneer WS Course
Posted on 22 July 2022With the release of the Wagoneer and the Grand Wagoneer WS, I-CAR has developed a course that overviews several features on the vehicles as well as repairability.
I-CAR Collision Reporter - The Customer Issue
Posted on 13 July 2022The nineteenth installment of the I-CAR Collision Reporter - The Customer Issue has been released. This issue focuses on the many customers of the entire inter-industry which I-CAR serves.
One-Time-Use Parts And Fasteners: FCA/Stellantis
Posted on 29 April 2022What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information?"
As the Repairability Technical Support (RTS) team researches OEMs for one-time-use fastener/part information, we are putting together a series of articles on how and where to locate this information for specific OEMs. Let’s take a look at FCA/Stellantis.
Locating OEM-Approved HV Tools: FCA/Stellantis
Posted on 19 April 2022When researching procedures for disabling a high-voltage (HV) vehicle, you may notice that many of the procedures require the use of specific tools. Some of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.
The RTS team is researching how to find these tools to make it easier for technicians performing these procedures. As we research the location of these special tools, we are compiling the information in a series of OEM-specific articles.
I-CAR Jeep Grand Cherokee WL Course
Posted on 15 March 2022The Jeep Grand Cherokee has undergone several changes starting into 2021. These changes being a body style change and, most importantly, structural changes. With the body style change, comes a new body code of Grand Cherokee (WL).
Calibration Research Tips: Jeep Grand Cherokee (WL)
Posted on 22 February 2022While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by year and model, even within a particular make. As the RTS team has been researching these systems, we have been identifying these atypical circumstances. In order to help you better understand them, we are putting together a series of articles that help with the repair and calibration of ADAS. Let’s take a closer look at the FCA/Stellantis Driver Assistance category in the Jeep Grand Cherokee (WL) service manual.
Locating OEM-Approved ADAS Tools: FCA/Stellantis
Posted on 2 December 2021When researching calibration procedures for advanced driver assistance systems (ADAS), you may notice that many of the procedures require the use of specific tools. Some tools may be everyday items like string, tape, levels, paper, etc. However, many of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.
FCA/Stellantis Non-Structural Guide
Posted on 29 October 2021The FCA/Stellantis Non-Structural Sheet Metal Repair guide is a document that provides additional information for when a non-structural repair is needed but not specified in the main body repair manual (BRM). Let’s take a look at what this document can help you with.
FCA/Stellantis Free Body Repair Manuals No Longer Available
Posted on 27 October 2021As you may know, FCA/Stellantis has removed the body repair manuals and Reference Guides from their free website www.moparrepairconnect.com.
Jeep Gladiator Door Gap
Posted on 10 September 2021The Gladiator brought a new look to the world of Jeep vehicles in 2020, and with that, comes a new detail to keep an eye out for. In the body repair manual (BRM), FCA/Stellantis calls attention to an issue with the doors that technicians should check for during installation.
FCA/Stellantis Website Navigation Video: UPDATE
Posted on 23 August 2021FCA/Stellantis has updated their stellantisiop.com service and repair information pay site.
Fiat Chrysler Automobiles Becomes Stellantis
Posted on 10 August 2021Fiat Chrysler Automobiles (FCA) and the French PSA Group has merged to become the vehicle maker Stellantis.
FCA/Stellantis Position Statement: Steering System
Posted on 1 April 2021FCA/Stellantis released a position statement related to steering system inspection and part replacement after a collision.
OEM Emergency Response Guides
Posted on 25 February 2021Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
FCA/Stellantis: Who Requires Or Recommends MIG Brazing?
Posted on 3 February 2021In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S. Let’s see what FCA/Stellantis has to say.
Repairer Driven News: 2021 Jeep Grand Cherokee L
Posted on 12 January 2021Repairer Driven News (RDN) released an article on the 2021 Jeep Grand Cherokee which outlines the variety of materials used in the construction of the vehicle which not only reduce weight but allow for easier stamping of complex parts.
Who Requires Or Recommends MIG Brazing? UPDATE
Posted on 25 November 2020In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S.
FCA/Stellantis ADAS Repair Planning: Do You Have All The Information?
Posted on 22 September 2020While researching body repair manuals (BRM) and service manuals, we're creating OEM-specific articles for additional information needed when repair planning. The goal of these articles is to help repairers create a more complete and accurate repair plan. One key aspect of repair planning is being aware of the advanced driver assistance systems (ADAS) equipped on the vehicle. Let’s take a closer look at FCA/Stellantis.
Repairer Driven News: 2021 Jeep Wrangler 4xe Plug-In Hybrid
Posted on 4 September 2020Repairer Driven News (RDN) released an article on the 2021 Jeep Wrangler 4xe plug-in hybrid which features up to 25 miles of pure electric driving and all power modes available when shifted into 4 low.
Non-SRS Wiring Repairs: FCA/Stellantis
Posted on 8 June 2020What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As technology increases on vehicles, so does the number of components that utilize electricity. Many of the sensors and modules are becoming smarter and more sensitive. If the wire is too long, the wrong gauge, or spliced in the wrong location, it can cause malfunctions in the components that it’s powering. Many OEMs have different restrictions and guidelines for repairing wiring that does not control SRS components. On the other hand, there are OEMs that don’t allow wiring repairs at all, so full harness replacement is the only option. Let’s take a closer look at FCA/Stellantis.
FCA/Stellantis Has Video Procedures
Posted on 14 May 2020Looking for more information about a specific repair procedure? Some OEMs are now providing videos within the repair procedures on their service site. Vehicle makers may also have additional websites that contain repair videos. As we research OEM websites and find these helpful videos, we will write articles to let you know. Let’s take a closer look at FCA/Stellantis.
Identifying The Correct Body Repair Manual: FCA/Stellantis
Posted on 14 January 2020Vehicle makers may group their body repair manuals (BRM) in several different ways. Sometimes the BRMs are grouped by a year range, some are listed as VIN specific, and others are arranged by a body code. Let’s take a look at FCA/Stellantis to see how they group their BRMs.
Identifying FCA/Stellantis Programming Differences
Posted on 18 December 2019While doing research on FCA/Stellantis for the RTS OEM Calibration Requirements Search, the RTS team noticed on some of the ADAS, there is a procedure called a “PROXI alignment”. We have researched what this means in order to give you clarity, in the event you see this procedure mentioned in the service manual.
FCA/Stellantis Position Statement: Glass Position Statement
Posted on 10 December 2019FCA/Stellantis has released a position statement on the use of non-OEM glass. The Authentic Mopar Glass Replacement position statement can be found on both the free and the paid websites.
Steel Spot And Plug Weld Nugget Size: FCA/Stellantis - UPDATE
Posted on 6 November 2019Did you know that some OEMs specify nugget size for spot and plug welds? This information is typically found within vehicle-specific repair procedures or can be found under general welding guidelines. Let’s see what FCA/Stellantis has to say.
Vehicle Technology And Trends 2020
Posted on 29 October 2019The 2020 model year vehicles are starting to roll off the assembly line and into showrooms. The I-CAR course, Vehicle Technology And Trends 2020, covers the technology, model releases, and trends. Keeping up-to-date on the 2020 models and features is vital to the blueprinting and repair process.
Sectioning And Partial Part Replacement: 2020 Jeep Gladiator
Posted on 18 October 2019One of the top technical inquires received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2020 Jeep Gladiator.
OEM Linking Pin: Refinishing Park Assist Sensors - FCA/Stellantis
Posted on 25 September 2019As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. Recently we had a technical inquiry that asked if FCA/Stellantis allows park assist sensors to be refinished.
Repairer Driven News: FCA/Stellantis Window Repair Tips For Jeep And RAM
Posted on 20 August 2019Repairer Driven News (RDN) released an article pertaining to repair procedures for three popular FCA/Stellantis vehicles. Technicians may want to take note of these tips for the panoramic sunroof of the 2019 RAM 1500, and stationary window repair on the 2018 Jeep Wrangler and 2020 Jeep Gladiator.
Advanced Driver Assistance Systems: 2019 Jeep Grand Cherokee
Posted on 19 August 2019While many have noticed that advanced driver assistance systems (ADAS), are showing up on vehicles, there still is confusion on what is required of these systems after a collision occurs. The Ask I-CAR team frequently get questions in regard to calibration of ADAS. Many of these questions can be answered simply by searching the OEM Calibration Requirements Search. However, there are some questions that may need more details than the calibration search provides. Let’s take a look at the 2019 Jeep Grand Cherokee ADAS.
FCA/Stellantis Color Codes To Identify Adhesives, Foams, And Seam Sealers
Posted on 28 June 2019Usage of adhesives, foams, and seam sealers has skyrocketed in recent years. Consumers demand their vehicles to be quieter, stronger, and last longer than ever before. With so much use of these materials, it can get confusing to figure out what material goes where, especially when looking at a diagram or a list of the required steps.
FCA/Stellantis Guidelines For Composite Reinforcements
Posted on 24 June 2019Stringent crash test ratings and fuel economy standards are making OEMs get creative with strengthening vehicles while maintaining or even lessening overall weight. Different materials are being used along with adding additional reinforcements. If you have repaired recent model year FCA/Stellantis vehicles, you may have noticed the usage of composite reinforcements.
FCA/Stellantis: Aluminum Body Panel Corrosion Repair
Posted on 1 April 2019Weight-saving aluminum is being used more and more on vehicles to aid in fuel economy. There has been a learning curve for collision technicians to be able to adapt to repairing aluminum. Also, with aluminum comes a form of oxidation that typically appears near the panel flanges. FCA/Stellantis addresses this issue and how to fix it in a recently released Collision Bulletin.
ADAS, Calibration, And Scanning Article Hotspot
Posted on 14 January 2019Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s Repairability Technical Support (RTS) team continues to be on the leading edge of research and education. Our goal is to help communicate information to the industry, and a great way to do this is through Collision Repair News articles.
FCA/Stellantis Announces Their New Midsize Truck: 2020 Jeep Gladiator
Posted on 13 December 2018FCA/Stellantis has developed an addition to the Jeep family that will be available in 2019, the 2020 Jeep Gladiator. This vehicle uses Jeep’s traditional body on frame design, with many other Jeep trademarks added into the overall look of the vehicle. Though the Gladiator may sport many of Jeep’s famous features, it brings some new materials and advanced driver assistance systems (ADAS) for collision repair technicians to be aware of.
Sectioning and Partial Part Replacement: 2018 Jeep Wrangler (JL)
Posted on 19 October 2018One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2018 Jeep Wrangler (JL).
Sectioning and Partial Part Replacement: 2018 Chrysler Pacifica
Posted on 12 October 2018One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2018 Chrysler Pacifica.
Sectioning and Partial Part Replacement: 2017 Jeep Cherokee
Posted on 26 September 2018One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2017 Jeep Cherokee.
I-CAR 360: 2018 Jeep Wrangler Video Now Available
Posted on 27 August 2018The I-CAR Repairability Technical Support (RTS) team recently developed a new I-CAR 360 video on the 2018 Jeep Wrangler. The video provides a 360° tour around the Wrangler. Let’s take a look.
Where Do I Find Other Types Of Information In FCA/Stellantis?
Posted on 20 June 2018Navigating OEM websites can be challenging when searching for collision repair procedures, especially as no two OEM websites are alike. What happens when you need to find other types of repair information, such as, "What needs to be inspected after a supplemental restraints system (SRS) deployment?", or "Does the tire pressure monitoring system (TPMS) require a scan tool or specialty tool?" Let's take a closer look at the FCA/Stellantis website.
Locating ADAS Information: FCA/Stellantis
Posted on 24 May 2018As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern vehicles. You may be required to look in numerous manuals to find the information required to safely repair the vehicle.
OEM Linking Pin: 2007-2017 Jeep Compass Ground Bolts
Posted on 1 February 2018Have you replaced the driver's side rail extension on a 2007 - 2017 Jeep Compass? Did you notice that the service part did not come with the ground bolts? What should you do?
All New Jeep Wrangler Body Repair Manual Available
Posted on 19 January 2018FCA/Stellantis unveiled the new Jeep Wrangler for 2018. The new Wrangler (JL) will be produced for some time, along with the past generation Wrangler (JK) Both will be 2018 model years. Though the traditional Jeep styling has not strayed far from its roots, the Wrangler (JL) is a very different vehicle.
Help With Flammable Foam
Posted on 9 January 2018Customer satisfaction is a major contributing factor to what goes into a new vehicle. One of the biggest demands from customers is a quiet passenger compartment. There are different ways of achieving a quiet cabin, like sound deadener pads, acoustic windshields, and specifically placed speakers that cancel noise. One method that is seen on every modern vehicle is noise vibration and harshness (NVH) foam.
Sectioning and Partial Part Replacement: 2017 Jeep Grand Cherokee
Posted on 1 December 2017One of the top technical inquiries received at Ask I-CAR, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2017 Jeep Grand Cherokee.
FCA/Stellantis: Welded Sheet Metal Repairs and Replacements
Posted on 9 November 2017The RTS team frequently receives inquiries on the sectioning and/or replacement of welded-on panels on FCA/Stellantis vehicles. The questions boil down to, what do you do when there isn’t a procedure available? Let’s revisit the FCA/Stellantis Collision Bulletin that addresses this.
Corrosion Protection Guidelines: FCA/Stellantis
Posted on 15 June 2017A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots that left untreated will lead to corrosion and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let’s take a look at what FCA/Stellantis says.
Additional Calibration Requirements: FCA/Stellantis
Posted on 11 May 2017The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.
Structural Sectioning Procedures: FCA/Stellantis
Posted on 30 March 2017Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.
Collision Information Website Access: FCA/Stellantis
Posted on 10 October 2016Why do I need a subscription to an OEM website if I have full subscription access to the I-CAR Repairability Technical Support (RTS) portal? This is a question received on a regular basis through Ask I-CAR. Let’s take a look at why and how to purchase an OEM subscription.
FCA/Stellantis Glass Replacement Requirements
Posted on 23 August 2016The role of the windshield is a lot more complex than simply allowing a view of the road ahead. It is considered a structural part of the vehicle as it contributes to the strength of the roof and A-pillars. The windshield helps to manage collision energy and has become an integral part of several advanced safety systems.
Always Follow Vehicle Maker Procedures
Posted on 7 July 2016We often receive Ask I-CAR inquiries asking: “what does I-CAR recommend?” Many times these questions are in regards to sectioning, straightening, or part replacement/attachment methods. Our first response is always:
FCA/Stellantis Position Statement: Pre- and Post-Repair System Scanning
Posted on 9 June 2016FCA/Stellantis has released a position statement related to pre- and post-repair system scanning.
Restraints Wiring Repairs
Posted on 23 May 2016Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
2015-16 RAM 1500 Modifications
Posted on 12 May 2016They may look the same on the outside, but they’re not on the inside. Did you know that in 2015, RAM updated the 1500 (DS) with modifications, reinforcement additions, and structural adhesive to improve collision impact performance?
FCA/Stellantis Has New Website Address For Repair Information
Posted on 12 August 2015FCA/Stellantis has updated the web address of the repair information website to stellantisiop.com. This new website changes how to find the collision repair information you need.
Step-By-Step: Accessing FCA/Stellantis Repair Information
Posted on 27 May 2015Per your requests, we are adding step-by-step instructions on how to access the vehicle maker repair information to complement our how-to-videos on the OEM Information pages. Easily reference this article by clicking the link under the videos on the following OEM pages:
FCA/Stellantis Collision Bulletin: UPDATE
Posted on 31 December 2014We've added the Safety Certification and Tire Pressure Label Replacement Guidelines Collision Bulletin from FCA/Stellantis that addresses safety certification and tire pressure label replacement guidelines.
What's A Chrysler/Dodge/Jeep/RAM Shotgun?
Posted on 29 December 2014When it comes to repair information, vehicle makers use a wide variety of terminology for replacement parts, but Chrysler, Dodge, Jeep, and RAM keep it pretty basic.
Minimum Driveaway Time For Urethane Adhesive
Posted on 3 October 2014I-CAR recognizes minimum driveaway time for urethane adhesive. This is a time specification that the glass industry has agreed on when a vehicle that has had a stationary glass replacement can be released to the customer. It is when the adhesive has achieved enough strength to pass Federal Motor Vehicle Safety Standards (FMVSS) 212, windshield retention, and 208, occupant protection.
Weld-Through Primer Requirements On The OEM Technical Information Matrix
Posted on 28 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The eighth column calls out if the vehicle maker requires the use of weld-through primer on flanges in preparation for welding.
Collision Repair Attachment Methods, Description, And Equipment Requirements Information On The OEM Technical Information Matrix
Posted on 13 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The seventh column calls out if the vehicle maker has information in regard to the recommended attachment method and the equipment required for complete, quality, and safe repairs.
Is There a Procedure for Disassembling a Service Assembly?
Posted on 19 June 2014The fourth column in the OEM Technical Information Matrix: Partial Service Part/Assembly Replacement Procedures at Factory Seams, can get a little tricky without further clarification. For the most part, this is a column that I-CAR is still researching published OEM information to get the answers to. The question is: Does the vehicle maker have procedures for replacing a partial service part or assembly at factory seams?
Weld Bonding Required on FCA/Stellantis Vehicles
Posted on 20 May 2014So you've got a Chrysler sitting in your repair facility and a service part, but no installation procedure. What do you do? On any other steel vehicle, you would duplicate the original attachment method and plug welds are ok, but not a Chrysler.
Can You Section An FCA/Stellantis Vehicle Without A Procedure?
Posted on 2 April 2014Did you know that in 2011, the Chrysler Group (FCA/Stellantis) published a position statement that identifies that parts should be installed in their entirety unless there is a procedure? This is applicable to all lines including Chrysler, Jeep, Dodge, Ram, Fiat, and SRT.
Working With Boron-Alloyed Steel - What's In A Name? (UHSS)
Posted on 26 March 2014Vehicle makers each have their own way of organizing their repair information. The names of the materials and even the names of different parts of vehicles may vary.
Three-Dimensional Measuring Equipment - Is It Really Necessary?
Posted on 8 September 2011I-CAR has been emphasizing the importance of three-dimensional measuring since its founding in 1979, but is it really required to repair a vehicle? After all, three-dimensional measuring systems are considerably more expensive compared to the much more affordable tape measure or tram gauge (see Figure 1).
Corrosion Protection To Structural Part Interiors
Posted on 4 August 2011There has been a longstanding recommendation to apply epoxy primer, as well as anti-corrosion compound, on the inside of rails and pillars and rocker panels as a last step for structural repairs. Going back as far as the July/August 1988 I-CAR Advantage, in the article "Restoring Corrosion Protection," is the following step for providing corrosion protection to enclosed interior surfaces: "Apply primer. Two-part epoxy recommended. Then apply anti-corrosion compound." The reason given, is that on areas where the coatings have been entirely removed, this is a two-step process that is replacing the two original coatings, zinc and E-coat.
Kia News
Kia Part Replacement Without A Procedure
Posted on 29 January 2026We are often asked, “What do I do if there isn’t a procedure to replace a service part?” Let’s see what Kia says.
Body Repair Manual Symbols: Kia
Posted on 17 September 2025While looking at repair procedures in a body repair manual (BRM) you may notice that symbols are used to indicate specific operations or parts to be used during the repair process. Most BRMs provide a glossary or a chart that explains these symbols.
Backup Battery And Low-Voltage Disconnect: Kia
Posted on 6 August 2025When an accident happens, how will you call for help? Maybe the telematics system, equipped with a backup battery, could automatically do this, even if the main power is cut off. What are the repair considerations, and where can information be found for backup batteries? Let’s see what Kia has to say.
I-CAR OEM Technical Information Matrix: What Is It, And How Does It Help? UPDATE
Posted on 5 December 2024Do you know which vehicle makers have collision repair information available? Do you know where you can go to find that out?
OEM Linking Pin: Kia Outer Uniside Sectioning
Posted on 10 May 2024As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. We’ve had technical inquiries that asked about sectioning and removing the outer uniside only, without the reinforcement and inner uniside.
High-Voltage Vehicle Paint Booth Quick Reference
Posted on 9 April 2024When refinishing high-voltage (HV) vehicles, it is important to check for OEM paint booth temperature recommendations so that HV components do not get damaged in the heat.
Kia High-Voltage Technician Levels: UPDATE
Posted on 5 December 2023As electric-only, hybrid, and fuel cell electric vehicles are increasing in sales, they are becoming more commonplace in repair facilities. Along with the unique powertrains that come with these vehicles, also comes unique safety concerns. Regardless of vehicle maker, high-voltage (HV) systems pose a threat of injury or death if not handled properly. Only personnel with the proper training, PPE, tools, equipment, and service information should perform work on the HV systems.
High-Voltage Handling And Storage Considerations: Kia
Posted on 29 November 2023High-voltage (HV) vehicles have some special considerations for handling and storing HV batteries and other components. The dangers of HV batteries are potential even after removal which is why certain precautions are needed. Let’s see what Kia has to say.
One-Time-Use Parts And Fasteners: Kia
Posted on 16 September 2022What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information?"
Locating OEM-Approved HV Tools: Kia
Posted on 27 May 2022When researching procedures for disabling a high-voltage (HV) vehicle, you may notice that many of the procedures require the use of specific tools. Some of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.
The RTS team is researching how to find these tools to make it easier for technicians performing these procedures. As we research the location of these special tools, we are compiling the information in a series of OEM-specific articles.
OEM Linking Pin: Kia Seat Belt Replacement
Posted on 24 February 2022As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. Recently, we had a technical inquiry that asked for clarification on seat belt replacement after a collision.
Identifying The Correct Body Repair Manual: Kia
Posted on 29 September 2021Vehicle makers may group their body repair manuals (BRM) in several different ways. Sometimes the BRMs are grouped by a year range, some are listed as VIN specific, and others are arranged by a body code. Let’s take a look at Kia to see how they group their BRMs.
Locating OEM-Approved ADAS Tools: Kia
Posted on 12 August 2021When researching calibration procedures for advanced driver assistance systems (ADAS), you may notice that many of the procedures require the use of specific tools. Some tools may be everyday items like string, tape, levels, paper, etc. However, many of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.
The RTS team is researching how to find these tools to make it easier for technicians performing these procedures. As we research the location of these special tools, we are compiling the information in a series of OEM-specific articles. Let’s see where you can find Kia-approved tool information.
OEM Emergency Response Guides: Kia
Posted on 23 July 2021Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Bumper Cover Repair With ADAS: Kia
Posted on 14 July 2021A simple bumper repair on a modern vehicle may not be as simple as it seems. New technologies like blind spot monitoring, adaptive cruise control, and other advanced driver assistance systems (ADAS) utilize sensors behind the bumper covers. The ability for these sensors to be able to see clearly normally requires special caution when considering a bumper repair. Many OEMs have different levels of warnings when it comes to repairing bumper covers with ADAS. So, what does Kia say on the subject?
Kia: Who Requires Or Recommends MIG Brazing?
Posted on 30 March 2021In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S. Let’s see what Kia has to say.
OEM Emergency Response Guides
Posted on 25 February 2021Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Who Requires Or Recommends MIG Brazing? UPDATE
Posted on 25 November 2020In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S.
Kia Has Video Procedures
Posted on 9 June 2020Looking for more information about a specific repair procedure? Some OEMs are now providing videos within the repair procedures on their service site. Vehicle makers may also have additional websites that contain repair videos. As we research OEM websites and find these helpful videos, we will write articles to let you know. Let’s take a closer look at Kia.
Sectioning And Partial Part Replacement: 2020 Kia Telluride
Posted on 27 May 2020One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacemet Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2020 Kia Telluride.
Calibration Research Tips: Kia Blind Spot Systems
Posted on 7 May 2020While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by year and model, even within a particular make. As the RTS team has been researching these systems, we have been identifying these atypical circumstances. In order to help you better understand them, we are putting together a series of articles that help with the repair and calibration of ADAS. Let’s take a closer look at the Kia blind spot systems.
Steel Spot And Plug Weld Nugget Size: Kia - UPDATE
Posted on 18 March 2020Did you know that some OEMs specify nugget size for spot and plug welds? This information is typically found within vehicle-specific repair procedures or can be found under general welding guidelines. Let's see what Kia has to say.
Repairer Driven News: 2020 Kia Cadenza
Posted on 7 February 2020Repairer Driven News (RDN) released an article about the 2020 Kia Cadenza. The article focuses on changes to the new generation of this Kia. These changes go beyond just the new exterior design.
Kia Collision Repair Overview
Posted on 4 November 2019The Kia Collision Repair Overview course has a lot of information that will help you throughout the repair process. Some information you will find in the course includes:
Vehicle Technology And Trends 2020
Posted on 29 October 2019The 2020 model year vehicles are starting to roll off the assembly line and into showrooms. The I-CAR course, Vehicle Technology And Trends 2020, covers the technology, model releases, and trends. Keeping up-to-date on the 2020 models and features is vital to the blueprinting and repair process.
I-CAR 360: 2019 Kia Optima Video Now Available
Posted on 14 October 2019The I-CAR Repairability Technical Support (RTS) team recently developed a new I-CAR 360 video on the 2019 Kia Optima. The video provides a 360° tour around the Optima. Let’s take a look.
Advanced Driver Assistance Systems: 2019 Kia Sportage
Posted on 2 October 2019While many have noticed that advanced driver assistance systems (ADAS) are showing up on vehicles, there still is confusion on what is required of these systems after a collision occurs. The Ask I-CAR team frequently gets questions in regard to calibration of ADAS. Many of these questions can be answered simply by searching the OEM Calibration Requirements Search. However, there are some questions that may need more details than the calibration search provides. Let’s take a look at the 2019 Kia Sportage ADAS.
OEM Linking Pin: 2016 Kia Optima JF/JFA
Posted on 10 July 2019As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. Recently, we had a technical inquiry that asked for clarification on the difference between the 2016-present Kia Optima JF and the Optima JFA.
Sectioning and Partial Part Replacement: 2019 Kia Optima
Posted on 28 June 2019One of the top technical inquiries received at Ask I-CAR, "Is there a sectioning or partial replacement procedure available?" To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let's take a closer look at the 2019 Kia Optima.
Industry Trends: Active Child Safety Lock
Posted on 15 February 2019Many people remember the good old days of the child lock, which was located in the jamb of the rear doors.
ADAS, Calibration, And Scanning Article Hotspot
Posted on 14 January 2019Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s Repairability Technical Support (RTS) team continues to be on the leading edge of research and education. Our goal is to help communicate information to the industry, and a great way to do this is through Collision Repair News articles.
Sectioning and Partial Part Replacement: 2018 Kia Stinger
Posted on 20 November 2018One of the top technical inquiries received at Ask I-CAR, "Is there a sectioning or partial replacement procedure available?" To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let's take a closer look at the 2018 Kia Stinger.
Non-SRS Wiring Repairs: Kia
Posted on 18 October 2018What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As technology increases on vehicles so does the number of components that utilize electricity. Many of the sensors and modules are becoming smarter and more sensitive. If the wire is too long, wrong gauge, or spliced in the wrong location it can cause malfunctions in the components that it’s powering. Many OEMs have different restrictions and guidelines for repairing wiring that does not control SRS components. On the other hand, there are OEMs that don’t allow wiring repairs at all, so full harness replacement is the only option.
Where Do I Find Other Types Of Information In Kia?
Posted on 17 July 2018Navigating OEM websites can be challenging when searching for collision repair procedures, especially as no two OEM websites are alike. What happens when you need to find other types of repair information, such as, "What needs to be inspected after a supplemental restraints system (SRS) deployment?", or "Does the tire pressure monitoring system (TPMS) require a scan tool or specialty tool?" Let's take a closer look at the Kia website.
Locating ADAS Information: Kia
Posted on 27 June 2018As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern vehicles. You may be required to look in numerous manuals to find the information required to safely repair the vehicle.
Kia Position Statement: Pre- and Post-Repair System Scanning
Posted on 14 June 2018Kia released a position statement recently relating to collision repair. Let’s take a look at what this statement is about.
Kia Collision Position Statements Available
Posted on 13 June 2018Kia’s position statements can now be accessed directly from the I-CAR RTS Portal. A quick link on the Kia OEM Information page will bring you right to the Kia position statements. Let’s take a look at what these position statements include.
Sectioning and Partial Part Replacement: 2017 Kia Optima
Posted on 15 December 2017One of the top technical inquiries received at Ask I-CAR, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2017 Kia Optima.
Corrosion Protection Guidelines: Kia
Posted on 18 August 2017A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots that left untreated will lead to corrosion and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let’s take a look at what Kia says.
Body Construction And Material Repair Guidelines: Kia
Posted on 8 August 2017What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
Structural Sectioning Procedures: Kia
Posted on 3 May 2017Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.
Additional Calibration Requirements: Kia
Posted on 28 April 2017The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.
Weld-Through Primer Guidelines: Kia
Posted on 9 February 2017Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Kia recommends and where this information can be found.
Collision Information Website Access: Kia
Posted on 14 November 2016Why do I need a subscription to an OEM website if I have full subscription access to the I-CAR Repairability Technical Support (RTS) portal? This is a question received on a regular basis through Ask I-CAR. Let’s take a look at why and how to purchase an OEM subscription.
Kia Glass Replacement Requirements
Posted on 7 September 2016The role of the windshield is a lot more complex than simply allowing a view of the road ahead. It is considered a structural part of the vehicle as it contributes to the strength of the roof and A-pillars. The windshield helps to manage collision energy and has become an integral part of several advanced safety systems.
Always Follow Vehicle Maker Procedures
Posted on 7 July 2016We often receive Ask I-CAR inquiries asking: “what does I-CAR recommend?” Many times these questions are in regards to sectioning, straightening, or part replacement/attachment methods. Our first response is always:
Restraints Wiring Repairs
Posted on 23 May 2016Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
Kia Restraints Wiring
Posted on 10 March 2016The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Kia's position on this subject.
Step-By-Step: Accessing Kia Repair Information
Posted on 1 June 2015Per your requests, we are adding step-by-step instructions on how to access the vehicle maker repair information to complement our how-to-videos on the OEM Information pages. Easily reference this article by clicking the link under the video on the Kia OEM Information page.
Kia Optima Bumper Cover Changes
Posted on 30 December 2014Having a problem getting your replacement Kia Optima bumper cover to fit properly? Wondering if maybe you got the wrong part?
Kia Collision Repair Information: UPDATE
Posted on 24 October 2014In previous I-CAR Collision Repair News articles, we announced the availability of comprehensive collision repair information from Kia.
Kia Adds 2015 Sedona Collision Repair Manual
Posted on 25 September 2014Kia Motors now has sectioning procedures available for the 2015 Sedona. This information has also been updated on the I-CAR developed OEM Partial Parts Replacement Search. The body repair manuals for Kia are available on the Kia free website at: www.kiatechinfo.com
Kia Adds New Collision Repair Manuals
Posted on 10 September 2014Kia Motors now has sectioning procedures available for the 2011-14 Sorento and the 2007-10 Rondo. This information has also been updated on the I-CAR developed OEM Partial Parts Replacement Search. The body repair manuals for Kia are available on Kia's free website at: www.kiatechinfo.com
Weld-Through Primer Requirements On The OEM Technical Information Matrix
Posted on 28 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The eighth column calls out if the vehicle maker requires the use of weld-through primer on flanges in preparation for welding.
Collision Repair Attachment Methods, Description, And Equipment Requirements Information On The OEM Technical Information Matrix
Posted on 13 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The seventh column calls out if the vehicle maker has information in regard to the recommended attachment method and the equipment required for complete, quality, and safe repairs.
What's A Kia Fender Apron Upper Panel?
Posted on 29 July 2014When it comes to repair information, vehicle makers use of a wide variety of terminology for replacement parts. All of the different names can be confusing, especially when repairing a variety of vehicle makes and models.
OEM Technical Information Matrix Update: Kia
Posted on 24 July 2014The OEM Technical Information Matrix has been updated to include Kia information. The corresponding, Collision Repair Information Availability chart has also been updated on the Kia-specific OEM Information page.
OEM Linking Pin: Kia Releases Collision Repair Manuals For Additional Models
Posted on 21 July 2014Kia Motors has released comprehensive collision repair manuals for most of their vehicles, in the United States!
Is There a Procedure for Disassembling a Service Assembly?
Posted on 19 June 2014The fourth column in the OEM Technical Information Matrix: Partial Service Part/Assembly Replacement Procedures at Factory Seams, can get a little tricky without further clarification. For the most part, this is a column that I-CAR is still researching published OEM information to get the answers to. The question is: Does the vehicle maker have procedures for replacing a partial service part or assembly at factory seams?
Kia Motors Releases Soul Collision Repair Manual
Posted on 10 January 2014Kia Motors has released a comprehensive collision repair manual for the Kia Soul, in the United States!
Land Rover News
Jaguar Land Rover Mechanical, Electrical, And Trim (MET) Training
Posted on 31 October 2025I-CAR now provides mechanical, electrical, and trim (MET) training for Jaguar Land Rover (JLR). This training is a new requirement for Jaguar Land Rover Authorized Collision Repair Centers.
Jaguar Land Rover Restraints Wiring: UPDATE
Posted on 14 August 2025The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Jaguar Land Rover's position on this subject.
OEM-Approved Connector And Pigtail Repair Resources: Jaguar Land Rover
Posted on 1 August 2025When confronted with a wiring harness repair, we often struggle to find the correct connector and pigtail repair kits. Often, a specific connector may be used on multiple applications. If the connector is allowed to be replaced, what resources are available to locate approved wiring connectors and pigtail repair kits? Let’s see what Jaguar Land Rover has to offer.
Structural Straightening On Jaguar Land Rover Vehicles
Posted on 7 February 2025What should you do when a damaged Jaguar Land Rover comes into your repair facility? Can it be straightened? What is a structural part? What type of equipment is required?
I-CAR OEM Technical Information Matrix: What Is It, And How Does It Help? UPDATE
Posted on 5 December 2024Do you know which vehicle makers have collision repair information available? Do you know where you can go to find that out?
Refinishing Park Assist Sensors: Jaguar Land Rover
Posted on 22 October 2024Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require painting to match the vehicle. Vehicle makers often provide information on the painting of new sensors. Some vehicle makers do not recommend refinishing sensors with minor finish damage because excessive paint thickness may adversely affect the operation of the park assist system. However, other vehicle makers allow refinishing and provide guidelines. Let’s see what Jaguar Land Rover (JLR) has to say.
Bumper Cover Repair With ADAS: Jaguar Land Rover - UPDATE
Posted on 13 June 2024A simple bumper repair on a modern vehicle may not be as simple as it seems. New technologies like blind spot monitoring, adaptive cruise control, and other advanced driver assistance systems (ADAS) utilize sensors behind the bumper covers. The ability for these sensors to be able to see clearly, normally requires special caution when considering a bumper repair. Many OEMs have different levels of warnings when it comes to repairing bumper covers with ADAS. So, what does Jaguar Land Rover say on the subject?
High-Voltage Vehicle Paint Booth Quick Reference
Posted on 9 April 2024When refinishing high-voltage (HV) vehicles, it is important to check for OEM paint booth temperature recommendations so that HV components do not get damaged in the heat.
OEM Emergency Response Guides: Jaguar Land Rover - UPDATE
Posted on 26 January 2024Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Locating OEM-Approved HV Tools: Jaguar Land Rover
Posted on 6 April 2023When researching procedures for disabling a high-voltage (HV) vehicle, you may notice that many of the procedures require the use of specific tools. Some of them are OEM-specific tools or scan tools. Often identifying and locating where to purchase these specific tools can be difficult.
Body Construction And Material Repair Guidelines: Jaguar Land Rover
Posted on 17 November 2022What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
As we know, today’s vehicles can be constructed from a wide variety of materials. Knowing if the OEM provides information on body construction materials and repair guidelines is a crucial step in providing a complete, safe, and quality repair. Let’s see what Jaguar Land Rover has to say.
Jaguar Land Rover High-Voltage Technician Levels
Posted on 1 September 2022As electric-only, hybrid, and fuel cell electric vehicles are increasing in sales, they are becoming more commonplace in repair facilities. Along with the unique powertrains that come with these vehicles, also comes unique safety concerns. Regardless of vehicle maker, high-voltage (HV) systems pose a threat of injury or death if not handled properly. Only personnel with the proper training, PPE, tools, equipment, and service information should perform work on the HV systems.
Non-SRS Wiring Repairs: Jaguar Land Rover
Posted on 17 June 2022What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As technology increases on vehicles, so does the number of components that utilize electricity. Many of the sensors and modules are becoming smarter and more sensitive. If the wire is too long, the wrong gauge, or spliced in the wrong location, it can cause malfunctions in the components that it’s powering. Many OEMs have different restrictions and guidelines for repairing wiring that does not control SRS components. On the other hand, there are OEMs that don’t allow wiring repairs at all, so full harness replacement is the only option.
One-Time-Use Parts And Fasteners: Jaguar Land Rover
Posted on 18 May 2022What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information?"
Identifying The Correct Body Repair Manual: Jaguar Land Rover
Posted on 28 April 2022Vehicle makers may group their body repair manuals (BRM) in several different ways. Sometimes the BRMs are grouped by a year range, some are listed as VIN specific, and others are arranged by a body code. Let’s take a look at Jaguar Land Rover to see how they group their BRMs.
Where Do I Find Other Types Of Information In Jaguar Land Rover?
Posted on 28 December 2021Navigating OEM websites can be challenging when searching for collision repair procedures, especially as no two OEM websites are alike. What happens when you need to find other types of repair information, such as, "What needs to be inspected after a supplemental restraint system (SRS) deployment?", or "Does the tire pressure monitoring system (TPMS) require a scan tool or specialty tool?" Let's take a closer look at the Jaguar Land Rover website.
Rivet Guns: Does My Shop Need Them?
Posted on 23 July 2021When performing collision repairs, there are more attachment methods available than ever before. OEMs specify which attachment methods are recommended or required. If a method is not listed as an option, it should not be used.
Jaguar Land Rover: Who Requires Or Recommends MIG Brazing?
Posted on 13 April 2021In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S. Let’s see what Jaguar Land Rover (JLR) has to say.
OEM Emergency Response Guides
Posted on 25 February 2021Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Repairer Driven News: Jaguar Land Rover Structural Composite Study
Posted on 27 January 2021Repairer Driven News (RDN) released an article on the Jaguar Land Rover (JLR) four-year research project that focuses on electric vehicles (EVs) and using composites to make lighter vehicles.
Sectioning And Partial Part Replacement: 2020 Land Rover Defender
Posted on 23 December 2020One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2020 Land Rover Defender.
Who Requires Or Recommends MIG Brazing? UPDATE
Posted on 25 November 2020In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S.
Locating ADAS Information: Jaguar Land Rover
Posted on 23 July 2020As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern vehicles. You may be required to look in numerous manuals to find the information required to safely repair the vehicle.
Repairer Driven News: 2020 Land Rover Defender
Posted on 27 September 2019Repairer driven news (RDN) released an article on the changes to the 2020 Land Rover Defender. This Defender is no longer a body over frame design. In fact, the structure of this vehicle is unlike any other Land Rover model with its own new platform. The “purpose-engineered” D7x platform was built to be the stiffest structure Land Rover has ever made. The body of this vehicle is aluminum intensive and lightweight.
Sectioning and Partial Part Replacement: 2019 Jaguar I-Pace
Posted on 18 September 2019One of the top technical inquires received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2019 Jaguar I-Pace.
How to Access Jaguar Land Rover Position Statements
Posted on 1 March 2019Jaguar Land Rover (JLR) position statements are only accessible through the Jaguar Land Rover service information site, TOPIx. From there, position statements can be accessed by Jaguar Land Rover network collision shops or by signing up for a free account. It is important to note that a free account does not provide access to the Workshop manuals.
Industry Trends: Active Child Safety Lock
Posted on 15 February 2019Many people remember the good old days of the child lock, which was located in the jamb of the rear doors.
Chicago Auto Show: 2020 Range Rover Evoque
Posted on 11 February 2019The newly redesigned Range Rover Evoque made its US debut at this years Chicago Auto Show. The new Evoque body style was inspired by the Range Rover Velar. Along with the overall body changes, the Evoque offers two engine options: gas powered and a 48-volt mild hybrid. But that’s not all!
ADAS, Calibration, And Scanning Article Hotspot
Posted on 14 January 2019Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s Repairability Technical Support (RTS) team continues to be on the leading edge of research and education. Our goal is to help communicate information to the industry, and a great way to do this is through Collision Repair News articles.
Jaguar Land Rover Position Statements Available
Posted on 7 January 2019There's a new addition to the OEM Information page for Jaguar Land Rover. An icon has been added that will link you to a page containing collision repair position statements.
Jaguar Land Rover Position Statement: Pre- and Post-Repair System Scanning
Posted on 2 January 2019As with many other OEMs, Jaguar Land Rover (JLR) has a published position statement available on pre- and post-repair scanning. Jaguar Land Rover credits advancements in technology with the need for scanning.
Sectioning and Partial Part Replacement: 2018 Land Rover Range Rover Velar
Posted on 14 December 2018One of the top technical inquiries received at Ask I-CAR is, “Is there a sectioning or partial replacement procedure available?” To help answer this question, RTS has an OEM Partial Part Replacement Search available. Here you will find information on if these procedures are available on a specific vehicle. Let’s take a closer look at the 2018 Land Rover Range Rover Velar.
Corrosion Protection Guidelines: Jaguar Land Rover
Posted on 10 August 2017A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots that left untreated will lead to corrosion and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let’s take a look at what Jaguar Land Rover (JLR) says.
Additional Calibration Requirements: Jaguar Land Rover
Posted on 14 July 2017The addition of the OEM Calibration Requirements Search to the RTS portal was a big step for the collision industry. While this new feature has been well received, there has been some confusion about what is included in the search tool. The OEM Calibration Requirements Search is designed to provide information on the calibration requirements that are needed for vehicles equipped with advanced driver assistance systems (ADAS). This includes systems such as adaptive cruise control, lane keep assist, and collision braking.
Structural Sectioning Procedures: Jaguar Land Rover
Posted on 23 June 2017Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.
Weld-Through Primer Guidelines: Jaguar Land Rover
Posted on 31 January 2017Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Jaguar Land Rover (JLR) recommends and where this information can be found.
Jaguar Land Rover Glass Replacement Requirements
Posted on 3 November 2016The role of the windshield is a lot more complex than simply allowing a view of the road ahead. It is considered a structural part of the vehicle as it contributes to the strength of the roof and A-pillars. The windshield helps to manage collision energy and has become an integral part of several advanced safety systems.
Always Follow Vehicle Maker Procedures
Posted on 7 July 2016We often receive Ask I-CAR inquiries asking: “what does I-CAR recommend?” Many times these questions are in regards to sectioning, straightening, or part replacement/attachment methods. Our first response is always:
Restraints Wiring Repairs
Posted on 23 May 2016Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
What's A Land Rover Fender Apron Panel?
Posted on 3 March 2016When it comes to repair information, vehicle makers use a wide variety of terminology for replacement parts. All of the different names can be confusing, especially when repairing a variety of vehicle makes and models.
Step-By-Step: Accessing Land Rover Repair Information
Posted on 27 April 2015Per your requests, we are adding step-by-step instructions on how to access the vehicle maker repair information to complement our how-to-videos on the OEM Information pages. Easily reference this article by clicking the link under the video on the Land Rover OEM Information page.
Today’s Advanced Vehicles Require Changes in Collision Repair Attachment Methods - Part 1
Posted on 20 December 2014This article originally appeared in the November/December edition of Fixed Ops Magazine.
Collision repair professionals are no different than any other professional – we are resistant to change. It took many years for repairers to make the switch to “MIG welding” for welding early unibody vehicles. (For this article we’ll use the term gas metal arc welding (GMAW) metal inert gas (MIG), or GMA (MIG)). (More on the reason, later.) It was a technology that was unfamiliar to many and there wasn’t a perceived need for change. History would prove otherwise, as there may not be a collision repair business in the country that doesn’t have a GMA (MIG) welder.
Repair or Replace? – Material Tensile Strength Key to Repairability
Posted on 23 September 2014Repair or Replace? – Material Tensile Strength Key to Repairability
Jason Bartanen, I-CAR Director, Industry Technical Relations
The world of steels continues to evolve at a rapid pace and repair professionals need to keep up. In order to perform complete, safe, and quality repairs, it’s imperative to identify the type of material we’re working with, to know what is repairable, and know which options we have for part replacement when straightening is not an option.
Weld-Through Primer Requirements On The OEM Technical Information Matrix
Posted on 28 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The eighth column calls out if the vehicle maker requires the use of weld-through primer on flanges in preparation for welding.
Collision Repair Attachment Methods, Description, And Equipment Requirements Information On The OEM Technical Information Matrix
Posted on 13 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The seventh column calls out if the vehicle maker has information in regard to the recommended attachment method and the equipment required for complete, quality, and safe repairs.
It's Not Just About Aluminum
Posted on 30 July 2014Today's Vehicles Require Updated Collision Repair Tools And Training
by Jason Bartanen
Ever since the unveiling of the 2015 Ford F-150 at the North American International Auto Show in Detroit in January, the U.S. automotive industry has been buzzing about this game changing, aluminum intensive vehicle.
What's A Jaguar Fender Apron Panel?
Posted on 17 July 2014When it comes to repair information, vehicle makers use a wide variety of terminology for replacement parts. All of the different names can be confusing, especially when repairing a variety of vehicle makes and models.
Is There a Procedure for Disassembling a Service Assembly?
Posted on 19 June 2014The fourth column in the OEM Technical Information Matrix: Partial Service Part/Assembly Replacement Procedures at Factory Seams, can get a little tricky without further clarification. For the most part, this is a column that I-CAR is still researching published OEM information to get the answers to. The question is: Does the vehicle maker have procedures for replacing a partial service part or assembly at factory seams?
The Aluminum Difference
Posted on 9 December 2013What's Iowa Got To Do With It?
by Jason Bartanen
We've seen a lot of changes in vehicle technology over the years. With each of these changes come new challenges and new opportunities. When the unibody vehicle was introduced, repair professionals were required to change their approach to collision repair, from damage analysis through the repair process. With the introduction of GMA (MIG) welding, additional requirements for repairs included new training and equipment. And passive restraints systems presented a completely different type of challenge, involving electronics and diagnostics.
*Results are compiled from matches in OEM Partial Part Replacement, OEM Restraints System Part Replacement, and OEM Hybrid and Electric Vehicle Disable. Use the search bar at the top of the page to find relevant Collision Repair News articles.
What does the vehicle maker say?
The information that matters.
Does it need to be calibrated?
Can that part be sectioned?
What parts need to be replaced?
Where's the high-voltage disable procedure?
What are the OEM glass requirements?
What's the best practice for repairs?
How do you navigate the RTS portal?
Have a collision repair question?