Structural Sectioning Procedures: Maserati
- Posted on 09 December 2022
Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.
I-CAR Repairers Realm: Ford F-150 Lightning Overview - Now Available
- Posted on 08 December 2022
I-CAR had a discussion on the Ford F-150 Lightning.
2021 Nissan Rogue Trunk Floor Replacement: Reusable Crossmember
- Posted on 07 December 2022
The 2021-present Nissan Rogue (T33) has a trunk floor sectioning procedure that requires the removal of the rear floor crossmember. Let’s take a look at what Nissan says to do with the crossmember.
OEM Linking Pin: 2020 Chevrolet Tahoe Sectioning Through Quarter Glass - Joint Type
- Posted on 02 December 2022
As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. Recently, we had a technical inquiry that asked on the type of sectioning joint to be used in the quarter glass flange when sectioning the outer quarter panel on a 2020 Chevrolet Tahoe. The lap joint specified in the procedure would prevent the quarter glass from being seated properly. We reached out to GM for clarification.
Rolls-Royce Restraints Wiring
- Posted on 02 December 2022
The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Rolls-Royce position on this subject.
I-CAR Honda HR-V 2022 Electromechanical Repair And Collision Repair Course
- Posted on 01 December 2022
I-CAR has developed courses that overview several features on the 2022 Honda HR-V, as well as repairability.
One-Time-Use Parts And Fasteners: Hyundai
- Posted on 25 November 2022
What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information"?
Where Do I Find Other Types Of Information In Mercedes-Benz?
- Posted on 23 November 2022
Navigating OEM websites can be challenging when searching for collision repair procedures, especially as no two OEM websites are alike. What happens when you need to find other types of repair information, such as, "What needs to be inspected after a supplemental restraints system (SRS) deployment?", or "Does the tire pressure monitoring system (TPMS) require a scan tool or specialty tool?" Let's take a closer look at the Mercedes-Benz website.
Body Construction And Material Repair Guidelines: Maserati
- Posted on 22 November 2022
What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
As we know, today's vehicles can be constructed from a wide variety of materials. Knowing if the OEM provides information on body construction materials and repair guidelines is a crucial step in providing a complete, safe, and quality repair. Let’s see what Maserati has to say.
Body Construction And Material Repair Guidelines: Jaguar Land Rover
- Posted on 17 November 2022
What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
As we know, today’s vehicles can be constructed from a wide variety of materials. Knowing if the OEM provides information on body construction materials and repair guidelines is a crucial step in providing a complete, safe, and quality repair. Let’s see what Jaguar Land Rover has to say.
Corrosion Protection Guidelines: Genesis
- Posted on 16 November 2022
A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots, that left untreated will lead to corrosion, and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let’s take a look at what Genesis says.
One-Time-Use Parts And Fasteners: Mazda
- Posted on 11 November 2022
What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information"?
Body Construction And Material Repair Guidelines: Genesis
- Posted on 09 November 2022
What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
I-CAR Repairers Realm: Ford Mustang Mach-E Emergency Response Guide - Now Available
- Posted on 08 November 2022
I-CAR had a discussion on the Ford Mustang Mach-E Emergency Response Guide.
Day Four: I-CAR Live From The 2022 SEMA Show
- Posted on 05 November 2022
Day four of the numerous I-CAR and SCRS interviews and presentations at the 2022 SEMA Show.
-
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning
Thursday, 28 July 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
-
Pre- and Post-Repair System Scanning Statements
Wednesday, 9 January 2019
Are you wondering if a particular OEM or organization has a published statement on pre-repair and post-repair scanning? We have compiled a list of most of the statements on the subject, so you can...
-
ADAS, Calibration, And Scanning Article Hotspot
Monday, 14 January 2019
Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on...
-
Honda/Acura Position Statement: Pre- and Post-Repair System Scanning - UPDATE
Wednesday, 22 May 2019
Honda /Acura has updated their position statement on pre- and post-repair scanning to give more clarification on what is expected for scanning.
-
Quickly Identifying Outer Quarter Panels w/Rolled Hem Flanges
Monday, 5 March 2018
The I-CAR best practice article, Recycled Outer Quarter Panels w/Rolled Hem Flanges has gotten a lot of interest from the collision repair industry. It’s important to know which vehicles are...
-
General Motors Position Statement: Pre- and Post-Repair System Scanning
Friday, 21 October 2016
As the industry continues to ask, are pre- and post-repair scans necessary, General Motors provides their answer.
-
Restraints Wiring Repairs
Monday, 23 May 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
-
BMW Position Statement: Pre- and Post-Repair System Scanning - UPDATE
Friday, 10 April 2020
BMW has released a position statement related to pre- and post-repair system scanning. The statement applies to All vehicles equipped with on board diagnostics II (OBD II).
-
FCA/Stellantis Position Statement: Pre- and Post-Repair System Scanning
Thursday, 9 June 2016
FCA/Stellantis has released a position statement related to pre- and post-repair system scanning.
-
Typical Calibration Requirements For Forward Radar Sensors
Wednesday, 12 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system to not...
-
Structural Straightening On Jaguar Land Rover Vehicles
Friday, 7 February 2025
What should you do when a damaged Jaguar Land Rover comes into your repair facility? Can it be straightened? What is a structural part? What type of equipment is required?
-
Back-To-Basics: Plug Weld Prep Using A Spot Blaster
Thursday, 6 February 2025
Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. Plug weld prep is not only a key factor in a successful repair but also in productivity.
-
I-CAR Repairers Realm: Compressed Air Filtration - Now Available
Tuesday, 4 February 2025
I-CAR had a discussion on compressed air filtration.
-
Hyundai/Genesis Releases Use Of Heat Position Statements
Friday, 31 January 2025
Hyundai and Genesis released position statements about the use of heat. Let’s take a look at the position statements.
-
Hyundai/Genesis Releases Bumper Cover Repairability Position Statements
Friday, 31 January 2025
Hyundai and Genesis released position statements about repairing bumpers with advanced driver assistance systems (ADAS) sensors.
-
Weld-Through Primer Guidelines: Subaru - UPDATE
Wednesday, 29 January 2025
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion....
-
Corrosion Protection Guidelines: Rivian
Monday, 27 January 2025
A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots that left untreated...
-
Honda Has Released The 2025 CR-V e:FCEV Body Repair News
Friday, 24 January 2025
Honda has released a Body Repair News bulletin for the 2025 Honda CR-V e:FCEV (fuel cell electric vehicle). This document provides at-a-glance relevant information for this new model.
-
Weld-Through Primer Guidelines: FCA/Stellantis - UPDATE
Wednesday, 22 January 2025
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion....
-
Bumper Cover Repair With ADAS: Hyundai
Friday, 17 January 2025
A simple bumper repair on a modern vehicle may not be as simple as it seems. New technologies like blind spot monitoring, adaptive cruise control, and other advanced driver assistance systems (ADAS)...
- 2025
- February 2025 (3)
- January 2025 (13)
- 2024
- December 2024 (8)
- November 2024 (11)
- October 2024 (13)
- September 2024 (10)
- August 2024 (12)
- July 2024 (12)
- June 2024 (9)
- May 2024 (13)
- April 2024 (12)
- March 2024 (12)
- February 2024 (12)
- January 2024 (10)
- 2023
- December 2023 (8)
- November 2023 (12)
- October 2023 (11)
- September 2023 (11)
- August 2023 (12)
- July 2023 (9)
- June 2023 (11)
- May 2023 (12)
- April 2023 (11)
- March 2023 (12)
- February 2023 (10)
- January 2023 (11)
- 2022
- December 2022 (11)
- November 2022 (12)
- October 2022 (11)
- September 2022 (13)
- August 2022 (11)
- July 2022 (10)
- June 2022 (13)
- May 2022 (11)
- April 2022 (12)
- March 2022 (10)
- February 2022 (11)
- January 2022 (13)
- 2021
- December 2021 (13)
- November 2021 (11)
- October 2021 (13)
- September 2021 (14)
- August 2021 (12)
- July 2021 (15)
- June 2021 (17)
- May 2021 (14)
- April 2021 (14)
- March 2021 (21)
- February 2021 (15)
- January 2021 (14)
- 2020
- December 2020 (13)
- November 2020 (17)
- October 2020 (12)
- September 2020 (14)
- August 2020 (11)
- July 2020 (18)
- June 2020 (16)
- May 2020 (14)
- April 2020 (20)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)
- 2019
- December 2019 (13)
- November 2019 (19)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (20)
- May 2019 (19)
- April 2019 (20)
- March 2019 (21)
- February 2019 (18)
- January 2019 (18)
- 2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (21)
- July 2018 (20)
- June 2018 (21)
- May 2018 (17)
- April 2018 (19)
- March 2018 (22)
- February 2018 (15)
- January 2018 (20)
- 2017
- December 2017 (13)
- November 2017 (15)
- October 2017 (19)
- September 2017 (20)
- August 2017 (20)
- July 2017 (18)
- June 2017 (20)
- May 2017 (19)
- April 2017 (13)
- March 2017 (18)
- February 2017 (10)
- January 2017 (12)
- 2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (10)
- August 2016 (11)
- July 2016 (8)
- June 2016 (10)
- May 2016 (7)
- April 2016 (11)
- March 2016 (12)
- February 2016 (11)
- January 2016 (8)
- 2015
- December 2015 (9)
- November 2015 (7)
- October 2015 (9)
- September 2015 (7)
- August 2015 (11)
- July 2015 (7)
- June 2015 (5)
- May 2015 (7)
- April 2015 (8)
- March 2015 (8)
- February 2015 (9)
- January 2015 (10)
- 2014
- December 2014 (12)
- November 2014 (7)
- October 2014 (11)
- September 2014 (10)
- August 2014 (9)
- July 2014 (12)
- June 2014 (9)
- May 2014 (12)
- April 2014 (9)
- March 2014 (6)
- February 2014 (1)
- January 2014 (26)
