Refinishing Park Assist Sensors: Audi

Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require painting to match the vehicle. Vehicle makers often provide information on the painting of new sensors. Some vehicle makers do not recommend refinishing sensors with minor finish damage because excessive paint thickness may adversely affect the operation of the park assist system. However, other vehicle makers allow refinishing and provide guidelines. Let’s see what Audi has to say.

Audi does not have published information regarding park assist sensor refinishing, so we reached out to see if we could get any additional information or insight from Audi.

Per our contact, the following must be followed to avoid malfunctions in the park assist system:

“Painting new parts:

  • Maximum layer thickness 125 microns; a measurement of layer depth is absolutely essential following application of the paint
  • Maximum curing temperature: 1 hour at 90°C

Painting used parts:

  • Remove old finish (sand) only as far as the primer
  • Minimum layer depth of 5–10 microns must remain
  • Maximum layer thickness 125 microns; a measurement of layer depth is absolutely essential following application of the paint
  • Maximum hardening temperature 1 hour at 90°C"

In order to accurately take a measurement of the paint thickness on a sensor, start by taking a reading of a sensor with no paint, then subtract that figure from the measurement of the painted sensor to get the actual thickness of the material. A paint thickness gauge that works with non-ferrous metal and plastic substrates must be used.

Our contact went on to state, that in addition to paint layer thickness, the following needs to be adhered to as well:

“Cleaning:
Immersion in cleaning solutions without previous masking of the plug terminals is prohibited.

Painting Area:
The face and side surfaces of membrane of the sensor are only to be painted. The painting of the side areas ranges from a minimum of 3 to a maximum 4 mm from the face side of the membrane to the rear.”

To clarify, this means that only the membrane part of the sensor is to be painted, the rest of the sensor must not be painted.

Audi requires an operation check be completed. This information can typically be found in the service manual under: Electrical Equipment, General information ➤ Rep. Gr. 97 ➤ Lines/Wiring ➤ Vehicle Diagnostic, Measuring and Information System.

Follow OEM procedures and warnings to help ensure a complete, safe, and quality repair.

For additional Audi information, check out the Audi OEM Information page.

Additional I-CAR Collision Repair News you may find helpful:


Related I-CAR Courses

  • Repairer Driven News: Rivian Updates Door Handle Procedure Sunday, 4 February 2035

    Repairer Driven News (RDN) released an article featuring an updated Rivian procedure.

  • 2025 SkillsUSA National Competition Results Monday, 30 June 2025

    The 2025 SkillsUSA National Leadership and Skills Conference took place on June 26, 2025. Every year I-CAR sends volunteers (virtually in 2021) to judge the collision repair technology competition....

  • Ford/Lincoln Rocker Panel Reinforcement Sectioning Friday, 27 June 2025

    We are often asked, “Can I section this panel?” Let’s take a look at Ford/Lincoln vehicles and sectioning the rocker panel reinforcement.

  • Back-To-Basics: Backside Panel Refinish And Edging Thursday, 26 June 2025

    Sometimes, going back to the basics can make the difference between a quality repair and a failed repair. When repairing and refinishing, you might need to refinish the panel's backside and edges.

  • Hyundai Position Statement: Pre- And Post-Repair System Scanning - UPDATE Monday, 23 June 2025

    Hyundai released an updated position statement relating to pre- and post-repair system scanning.

  • App-Based Connected Services Considerations Tuesday, 17 June 2025

    Have you had an experience where the vehicle notified the owner that it was being moved while it was in your repair facility? App-based connected services are available from many vehicle makers and...

  • Digital Key Considerations Tuesday, 17 June 2025

    The intermingling of technology and automobiles continues, with digital key offerings from most vehicle makers. Digital keys utilize smartphone technology to expand vehicle access and owner...

  • Back-To-Basics: Tire Tread Pattern Wednesday, 11 June 2025

    Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. Let’s see how to identify tire tread patterns and their repair considerations.

  • Corrosion Protection Guidelines: Ford/Lincoln - UPDATE Tuesday, 10 June 2025

    A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots that, left untreated,...

  • Rivian Restraints Wiring Thursday, 5 June 2025

    The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Rivian's position on this subject.