Nitrogen Hot Air Welding

Hot air welders have been around for a number of years and used mostly in bumper remanufacturing facilities. A hot air welder works by passing compressed air over a heating element and heating the air to around 345°C (650°F) to melt the base plastic and filler rod/ribbon together. This type of welder does not use a flat shoe or feeder tube-type tip. A V-groove is cut into the part, the rod is laid into the V-groove, and the two are melted together. Whenever using this type of welder, it is important to have airflow over the element at all times no matter if it is preheating, welding, or cooling.
A nitrogen hot air welder uses compressed nitrogen gas to eliminate oxygen from the weld area. The nitrogen acts as a shielding gas and allows for a contaminant-free weld with less smoke, which creates a stronger weld (see Figure 1). This type of welder can also switch to compressed air so that when preheating, or cooling down the heating element, it does not waste the nitrogen.
A fusion weld is made when the welding rod and plastic melt and mix together. This type of weld can only be done on thermoplastics. Thermoplastics, such as polypropylene/thermo plastic polyolefin (PP/TPO), which is used to make most bumper covers today, work very well with this type of welder.
Making a Repair
Figure 2 - Whenever possible, match the ISO code on the part to the filler material.Before any sanding or grinding starts, the part must first be cleaned with soap and water, followed by cleaning with the recommended cleaner. It is also recommended to wipe in one direction to help reduce static. If this step is skipped, the repair may fail due to contamination in the repair area. Once the plastic has been abraded, no solvent cleaners should be used because if any of the solvents become trapped under the repairs it could bubble the repair area in the bake cycle or when it is exposed to the sun.
Identification
When making a nitrogen hot air plastic weld, the need for plastic identification is essential to a successful repair. The plastic identification is primarily used to determine which rod will match the plastic part. It is also helpful to know how the plastic will melt because different plastics will melt at different temperatures. One way to identify the type of plastic is to look at the ISO code that should be located on the backside of the part (see Figure 2). If the ISO code cannot be found, the vehicle maker may have a listing of the types of plastic their parts are made of and may even have a recommended repair procedure.
Once the base material is identified, the technician can select the filler rod to use. Plastic welding rods are usually made of a pure plastic like polypropylene (PP), acrylonitrile butadiene styrene (ABS) or thermoplastic olefin (TPO). Therefore, they may not match a specific blend of plastic base material. They are available in different diameters and shapes. Some are round rods and others are a flat ribbon. There are also different widths of flat ribbon with the wide ribbons used on the backside as a reinforcement and the more narrow ribbon used as a filler on the front side.
Figure 3 - Protective gloves are recommended in order to prevent burns from the high heat of the nitrogen hot air welder.
Repair
After the part has been cleaned and the base material and filler rod have been identified, the part being repaired can be realigned and held in place using aluminum tape. Once the front side is realigned, the backside of the part can be sanded with about P80 grit. Following sanding, the area should be blown clean with clean, oilfree compressed air.
After the nitrogen hot air plastic welder is preheated, the nitrogen gas is turned on and the base material and the welding ribbon are preheated. As the base material and ribbon start to melt, the ribbon is pushed into the base material (see Figure 3). The ribbon will start to fuse to the base material and begin to squeeze out the sides of the ribbon. If a tear goes to an edge of a part, a second smaller ribbon can be laid down across the tear to form a "T" pattern at the edge of the part to add extra strength. Watch the video for a short demonstration of this process (see video).
Once the backside repairs are complete, the aluminum tape can be removed and the tear on the front side can be v-grooved. A v-groove is made on the front side to allow the repair ribbon to be laid down level or slightly lower than the surrounding plastic. Again, make sure that no paint is in the weld area. A smaller ribbon is placed into the v-groove using the same technique as on the backside. Once the weld area has cooled, it should be sanded down and, if necessary, a plastic repair filler should be applied to fill any imperfections.
Figure 4 - The technique used to make a nitrogen hot air weld is similar to that of a TIG weld.The acronym TAPS will help the technician remember all the different things to watch while making a nitrogen hot air plastic weld (see Figure 4). The "T" stands for temperature, which must be atthe correct setting to melt the part and the rod. The “A” stands for angle, which should be about 45º to the part. The “P” stands for pressure, which should be firm and constant. The “S” stands for speed, which should allow for 100–150 mm (4"–6") of material to be welded per minute.
Precautions
Some welding repair precautions are to never leave any shiny or melted plastic on the part. This will cause poor adhesion of any filler or refinish material. It is also important to featheredge the repair area to make it an invisible repair. With all plastics, never use a solvent on bare plastic. If the vehicle is equipped with an adaptive cruise control or parallel park assist systems, no repair should be done in front of a sensor if it impedes the ability of the sensor to function.
Conclusion
Nitrogen hot air plastic welders are another option to repair plastic parts that otherwise might be discarded. As with any repair technology, it is a business decision to choose to use a repair technology that works best for you.
Related I-CAR Courses
-
Pre- and Post-Repair System Scanning Position Statements
Wednesday, 09 January 2019
Are you wondering if a particular OEM or organization has a published position statement on pre-repair and post-repair scanning? We have compiled a list of most of the position statements…
-
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning
Thursday, 28 July 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
-
ADAS, Calibration, And Scanning Article Hotspot
Monday, 14 January 2019
Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s…
-
Restraints Wiring Repairs
Monday, 23 May 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
-
Typical Calibration Requirements For Blind Spot Sensors
Wednesday, 19 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Honda/Acura Position Statement: Pre- and Post-Repair System Scanning - UPDATE
Wednesday, 22 May 2019
Honda /Acura have updated their position statement on pre- and post-repair scanning to give more clarification on what is expected for scanning.
-
Typical Calibration Requirements For Forward Radar Sensors
Wednesday, 12 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
MIG Brazing What Is It, Why Should I Use It?
Monday, 02 June 2014
Why MIG Brazing? It is widely known that GMA welded; fully galvanized steel will lose some of its properties, including corrosion protection, due to the heat created during welding. OEMs…
-
FCA/Stellantis Position Statement: Pre- and Post-Repair System Scanning
Thursday, 09 June 2016
FCA/Stellantis has released a position statement related to pre- and post-repair system scanning.
-
Typical Calibration Requirements For Park Assist Sensors
Monday, 31 October 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
-
Back-To-Basics: Door Handle Tools
Friday, 22 September 2023
Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. Tools for the door handle might not sound exciting, but they can save you frustration,…
-
OEM Emergency Response Guides: Rivian
Wednesday, 20 September 2023
Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to…
-
I-CAR Repairers Realm: Lucid Motors Innovative Vehicles and Repair Network - Coming Soon
Tuesday, 19 September 2023
I-CAR is having a discussion on Lucid Motors innovative vehicles and repair network. Tune into Repairers Realm to listen and join in for questions and answers.
-
Locating ADAS Information: GM - UPDATE
Friday, 15 September 2023
As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern…
-
Hyundai/Genesis Releases Additional Body Repair Manuals: UPDATE
Thursday, 14 September 2023
Hyundai Motor America updated their approved body repair manuals (BRMs) available to the United States market. This includes both Hyundai and Genesis branded BRMs.
-
Structural Straightening On Tesla Vehicles: UPDATE
Wednesday, 13 September 2023
What should you do when a damaged Tesla comes into your repair facility? Can you measure it? Can it be straightened? What needs to be replaced?
-
I-CAR Repairers Realm: Ford Structural Sectioning Guidelines - Now Available
Friday, 08 September 2023
I-CAR had a discussion on Ford structural sectioning guidelines.
-
Calibration Research Tips: Honda/Acura Millimeter Wave Radar Mounting Position Inspection
Wednesday, 06 September 2023
While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by…
-
Locating ADAS Information: Maserati - UPDATE
Friday, 01 September 2023
As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern…
-
OEM-Approved Pigtail Connector Kit Resources: Nissan/INFINITI
Thursday, 31 August 2023
When confronted with a wiring harness repair, we often struggle finding the correct connector and pigtail repair kits. Often a specific connector may be used on multiple applications. If the…
- 2023
- September 2023 (9)
- August 2023 (12)
- July 2023 (9)
- June 2023 (12)
- May 2023 (12)
- April 2023 (11)
- March 2023 (13)
- February 2023 (10)
- January 2023 (11)
- 2022
- December 2022 (11)
- November 2022 (12)
- October 2022 (11)
- September 2022 (13)
- August 2022 (11)
- July 2022 (10)
- June 2022 (13)
- May 2022 (11)
- April 2022 (12)
- March 2022 (11)
- February 2022 (12)
- January 2022 (13)
- 2021
- December 2021 (15)
- November 2021 (12)
- October 2021 (13)
- September 2021 (15)
- August 2021 (12)
- July 2021 (16)
- June 2021 (17)
- May 2021 (14)
- April 2021 (14)
- March 2021 (21)
- February 2021 (15)
- January 2021 (14)
- 2020
- December 2020 (13)
- November 2020 (17)
- October 2020 (12)
- September 2020 (14)
- August 2020 (11)
- July 2020 (18)
- June 2020 (16)
- May 2020 (14)
- April 2020 (20)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)
- 2019
- December 2019 (13)
- November 2019 (19)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (21)
- May 2019 (19)
- April 2019 (20)
- March 2019 (21)
- February 2019 (21)
- January 2019 (18)
- 2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (21)
- July 2018 (20)
- June 2018 (21)
- May 2018 (17)
- April 2018 (19)
- March 2018 (22)
- February 2018 (17)
- January 2018 (20)
- 2017
- December 2017 (13)
- November 2017 (15)
- October 2017 (19)
- September 2017 (20)
- August 2017 (20)
- July 2017 (18)
- June 2017 (23)
- May 2017 (20)
- April 2017 (15)
- March 2017 (18)
- February 2017 (11)
- January 2017 (13)
- 2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (11)
- August 2016 (11)
- July 2016 (8)
- June 2016 (13)
- May 2016 (10)
- April 2016 (11)
- March 2016 (12)
- February 2016 (11)
- January 2016 (8)
- 2015
- December 2015 (9)
- November 2015 (8)
- October 2015 (9)
- September 2015 (7)
- August 2015 (11)
- July 2015 (10)
- June 2015 (8)
- May 2015 (8)
- April 2015 (9)
- March 2015 (8)
- February 2015 (9)
- January 2015 (11)
- 2014
- December 2014 (12)
- November 2014 (7)
- October 2014 (11)
- September 2014 (10)
- August 2014 (9)
- July 2014 (12)
- June 2014 (9)
- May 2014 (14)
- April 2014 (9)
- March 2014 (6)
- February 2014 (1)
- January 2014 (27)