I-CAR OEM Technical Information Matrix: What Is It, And How Does It Help? - UPDATE
Posted on 5 December 2024Do you know which vehicle makers have collision repair information available? Do you know where you can go to find that out?
Locating ADAS Information: Maserati - UPDATE
Posted on 1 September 2023As a collision repair technician, there is one part of a service manual that houses all of the information you would ever need…right? This is not the case with modern vehicles. You may be required to look in numerous manuals to find the information required to safely repair the vehicle.
Corrosion Protection Guidelines: Maserati
Posted on 16 March 2023A key factor in collision repair is making long-lasting repairs. When a vehicle is repaired, many areas of corrosion protection are disturbed. This creates corrosion hot spots, that left untreated will lead to corrosion, and potentially a repair failure. However, there are certain precautions that can be taken to safely and properly restore the corrosion protection, throughout the repair process. OEMs often give specifications on restoring corrosion protection. These specifications generally include seam sealer, adhesives, foam fillers, and cavity waxes. Let's take a look at what Maserati says.
Structural Sectioning Procedures: Maserati
Posted on 9 December 2022Ask I-CAR receives many technical inquiries referring to sectioning. The collision repair industry wants to know where can you section, does the OEM have a sectioning procedure, and where can I find the sectioning procedure? Most OEMs allow sectioning to outer body panels and the front and rear rails. Sectioning reinforcements is not as common, as most reinforcements are replaced at factory seams.
Body Construction And Material Repair Guidelines: Maserati
Posted on 22 November 2022What is the MPa of the front lower rail? What is the outer uniside made of: steel, aluminum, or composite? Can heat be used to straighten or is it cold straightening only? What are the repair limitations? These are just some of the questions that the RTS team fields on a daily basis.
As we know, today's vehicles can be constructed from a wide variety of materials. Knowing if the OEM provides information on body construction materials and repair guidelines is a crucial step in providing a complete, safe, and quality repair. Let’s see what Maserati has to say.
Non-SRS Wiring Repairs: Maserati
Posted on 28 October 2022What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As technology increases on vehicles, so does the number of components that utilize electricity. Many of the sensors and modules are becoming smarter and more sensitive. If the wire is too long, the wrong gauge, or spliced in the wrong location it can cause malfunctions in the components that it’s powering. Many OEMs have different restrictions and guidelines for repairing wiring that does not control SRS components. On the other hand, there are OEMs that don’t allow wiring repairs at all, so full harness replacement is the only option.
Maserati Restraints Wiring
Posted on 29 September 2022The question is often asked, "Can supplemental restraints system wiring be repaired?" The answer is: it depends on the vehicle maker. Let's take a look at Maserati’s position on this subject.
Fiat Chrysler Automobiles Becomes Stellantis
Posted on 10 August 2021Fiat Chrysler Automobiles (FCA) and the French PSA Group has merged to become the vehicle maker Stellantis.
Rivet Guns: Does My Shop Need Them?
Posted on 23 July 2021When performing collision repairs, there are more attachment methods available than ever before. OEMs specify which attachment methods are recommended or required. If a method is not listed as an option, it should not be used.
OEM Emergency Response Guides
Posted on 25 February 2021Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to webpages that house them, or provides articles with instructions on how to locate them.
Where Do I Find Other Types Of Information In Maserati?
Posted on 9 December 2020Navigating OEM websites can be challenging when searching for collision repair procedures, especially as no two OEM websites are alike. What happens when you need to find other types of repair information, such as, "What needs to be inspected after a supplemental restraints system (SRS) deployment", or "Does the tire pressure monitoring system (TPMS) require a scan tool or specialty tool?" Let's take a closer look at the Maserati website.
Who Requires Or Recommends MIG Brazing? UPDATE
Posted on 25 November 2020In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S.
Weld-Through Primer Guidelines: Maserati
Posted on 27 October 2020Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Maserati recommends and where this information can be found.
Maserati Glass Replacement Requirements
Posted on 15 September 2020The role of the windshield is a lot more complex than simply allowing a view of the road ahead. It is considered a structural part of the vehicle as it contributes to the strength of the roof and A-pillars. The windshield helps to manage collision energy and has become an integral part of several advanced safety systems.
What's A Maserati Lower Rear Guard?
Posted on 1 September 2020When it comes to repair information, vehicle makers use a wide variety of terminology for replacement parts. All of the different names can be confusing, especially when repairing a variety of vehicle makes and models.
Collision Information Website Access: Maserati
Posted on 3 April 2020Why do I need a subscription to an OEM website if I have full subscription access to the I-CAR Repairability Technical Support (RTS) portal? This is a question received on a regular basis through Ask I-CAR. Let’s take a look at why and how to purchase an OEM subscription.
Step-By-Step: Accessing Maserati Repair Information
Posted on 3 April 2020Per your requests, we are adding step-by-step instructions on how to access the vehicle maker service repair information to complement our how-to-videos on the OEM Information pages. Easily reference this article by clicking the link under the video on the Maserati OEM Information page.
ADAS, Calibration, And Scanning Article Hotspot
Posted on 14 January 2019Since advanced driver assistance systems (ADAS), scanning, and calibration first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s Repairability Technical Support (RTS) team continues to be on the leading edge of research and education. Our goal is to help communicate information to the industry, and a great way to do this is through Collision Repair News articles.
Always Follow Vehicle Maker Procedures
Posted on 7 July 2016We often receive Ask I-CAR inquiries asking: “what does I-CAR recommend?” Many times these questions are in regards to sectioning, straightening, or part replacement/attachment methods. Our first response is always:
Restraints Wiring Repairs
Posted on 23 May 2016Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
Maserati And Rolls-Royce OEM Information Pages
Posted on 24 November 2015The OEM Information pages continue to grow, here are a few of the new features for this area of the RTS portal.
Weld-Through Primer Requirements On The OEM Technical Information Matrix
Posted on 28 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The eighth column calls out if the vehicle maker requires the use of weld-through primer on flanges in preparation for welding.
Collision Repair Attachment Methods, Description, And Equipment Requirements Information On The OEM Technical Information Matrix
Posted on 13 August 2014Let's continue our breakdown of the columns in the OEM Technical Information Matrix. The seventh column calls out if the vehicle maker has information in regard to the recommended attachment method and the equipment required for complete, quality, and safe repairs.
Is There a Procedure for Disassembling a Service Assembly?
Posted on 19 June 2014The fourth column in the OEM Technical Information Matrix: Partial Service Part/Assembly Replacement Procedures at Factory Seams, can get a little tricky without further clarification. For the most part, this is a column that I-CAR is still researching published OEM information to get the answers to. The question is: Does the vehicle maker have procedures for replacing a partial service part or assembly at factory seams?
