OEM Restraints System Part Replacement Search
2013 Ford Focus
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).
1. Turn all vehicle accessories OFF.
2. Turn the ignition OFF.
3. At the BCM, located on the bulkhead below the glove box, remove the RCM fuse 86 (10A) from the BCM. Refer to Wiring Diagrams Cell 11 for schematic and connector information.
4. Turn the ignition ON and visually monitor the air bag indicator for at least 30 seconds. The air bag indicator will remain lit continuously (no flashing) if the correct RCM fuse has been removed. If the air bag warning indicator does not remain lit continuously, remove the correct RCM fuse before proceeding.
5. Turn the ignition OFF.
6. Disconnect the battery ground cable at the LF strut tower. Make sure that the ground cable is completely isolated from the vehicle chassis and cannot make electrical contact with any part of the vehicle chassis during service
7. Wait at least one minute before continuing vehicle service
REV: 04/2011
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When any deployable device or combination of devices have deployed and/or the RCM has DTC B1193:00 (Event Threshold Exceeded) in memory, the repair of the vehicle SRS is to include the removal of all deployed devices and the installation of new deployable devices, the removal and installation of new impact sensors and the removal and installation of a new RCM.Removal of all deployed devices and the installation of new deployable devices: [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL; AIRBAG,KNEE BOLSTER; AIRBAG,FRONT SEAT; AIRBAG,ROOF]
Removal and installation of new impact sensors and the removal and installation of a new RCM: [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,QTR PANEL; MODULE,AIRBAG CONTROL]
When the driver airbag has deployed, install a new clockspring
If a side air bag deployment took place, install a new seat backrest foam pad, backrest cover, deployment chute and side air bag module and nuts.
Install a New headliner and new A-, B-, C• and D-pillar upper trim panels and attaching hardware, if roof airbag deployed
New driver safety belt system (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the driver safety belt pretensioners, (If Deployed)
New Front passenger safety belt system (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the Front passenger safety belt pretensioner, (If Deployed)
Install new safety belt(s) at any seating position(s) where deployment has occurred and the safety belt(s) were used.
New second row safety belt systems (including retractors, buckles and inflators) must be installed if the vehicle is involved in a collision that results in deployment of the rear inflatable safety belt system.
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
When a vehicle has been involved in a collision and the OCSM has DTC B1193:00 stored in memory, the repair of the OCS is to include the following procedures for the specified system: For a bladder-type OCS, inspect for damage and repair as necessary. If installation of an OCS component is required, an OCS service kit must be installed.When any damage to the impact sensor mounting points or mounting hardware has occurred, repair or install new mounting points and mounting hardware as needed.
Inspect the entire vehicle for damage, including the following components:
• Steering column (deployable column if equipped)
• Instrument panel knee bolsters and mounting points
• Safety Canopy and mounting points
• Instrument panel braces and brackets
• Instrument panel and mounting points
• Seats and seat mounting points
• Safety belts, safety belt buckles, safety belt retractors and safety belt anchors
• SRS wiring, wiring harnesses and connectors
Before installing the new safety belt assembly, inspect the safety belt attaching areas for damage and distortion. If the attaching points are damaged and distorted, work the sheet metal back to its original shape and structural integrity.
Before installing a Safety Canopy® or side air curtain module, inspect the roofline for any damage. If necessary, the sheet metal must be reworked to its original condition and
structural integrity.
After carrying out the review and inspection of the entire vehicle for damage, repair or install new components as needed.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
