OEM Restraints System Part Replacement Search
2010 Honda Insight (Hybrid)
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
1) Turn the ignition switch to LOCK (0)2) Disconnect the negative cable from the 12 volt battery
3) Wait at least 3 minutes before starting work
Before disconnecting the SRS unit connectors, always disconnect the appropriate SRS parts connectors
REV: 03/2014
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a collision where the seat belt tensioners deployed, replace these items:• SRS unit [MODULE,AIRBAG CONTROL]
• Seat belt tensioners
• Front impact sensors [AIRBAG SENSOR,FENDER]
After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed airbag(s) [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL]
• Seat belt tensioners
• Front impact sensors [AIRBAG SENSOR,FENDER]
After a collision where the side airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor [AIRBAG SENSOR,FLOOR MTD]
• Seat frame(s) and related parts. After a collision where the side airbag was deployed, replace the side airbag, the seat frame and related parts with new parts. If the seat-back cushion is split, it must be replaced [AIRBAG,FRONT SEAT]
After a collision where a side curtain airbag has deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor [AIRBAG SENSOR,FLOOR MTD]
• A-pillar trim(s)
• B-pillar upper trim(s)
• C-pillar trim(s)
• Headliner
• Front grab handle(s)
• Rear grab handle(s)
• All related trim clips
• Sunvisor(s)
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Before doing any SRS repairs, check the DTCs, for the less obvious deployed components (seat belt tensioners, front impact sensors, side impact sensors, etc.).• If there is a breaking or damage found in harness relevant to the [SRS] replacement parts, replace it, do not repair.
• Do not replace the ODS unit unless it is physically damaged or a specific fault was found during DTC troubleshooting. Because it could complicate troubleshooting other DTCs
• After a vehicle collision, do the ODS unit operation check
• After a vehicle collision, inspect the front seat active head restraint
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. Replace the components as needed.
• Inspect all the SRS wire harnesses. Replace, do not repair, any damaged harnesses
• Inspect the cable reel for heat damage. If there is any damage, replace the cable reel [CLOCK SPRING]
• Check the front passenger's weight sensor output, after a vehicle collision
• Replace all damaged parts
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
