OEM Restraints System Part Replacement Search
2007 BMW X5 3.0i/3.0is/4.8i
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
• Inspection, testing and installation work may only be carried out by expert trained personnel in BMW Service.• Work on components of the airbag system should only ever be carried out with the battery disconnected, the negative terminal post covered and the plug connection of the cable leading to the gas generator disconnected. If only the battery is
disconnected, the following prescribed waiting period must be observed without fail:
1 minute for vehicles from 9/93
• When carrying out straightening and welding work with an electric welder:
• Disconnect battery
• Cover negative terminal (post)
REV: 04/2013
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
Replace the following components after airbag triggering:• Steering wheel, [if Driver airbag module Deployed]
• Driver airbag module [AIRBAG,STEERING WHEEL], [if Deployed]
• Passenger airbag module [AIRBAG,INSTRUMENT PNL], [if Deployed]
• Replace airbag module [AIRBAG,FRONT SEAT], [if Deployed] and, if necessary, seat cover with padding
• Replace gas generator, active head restraint system [UNIT,ACTIVE HEADREST]. If the severity of the impact has not caused any other damage to the seat, only the triggered gas generator needs to be replaced
• Roof Airbag module [AIRBAG, ROOF], [if Deployed]
NOTE: Head restraint: The firing unit may be replaced up to 5 times. Triggering frequency is denoted on the sticker on the head restraint carrier. Stickers are available as spare parts. The complete crash-active head restraint must be replaced in the event of a head restraint fault signal and an untriggered firer
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Check and/or replace following components after airbag triggering:Satellites (control unit + sensor):
• Acceleration Sensor [AIRBAG SENSOR,FRONT]
• Satellite, A-/B-pillar, left/right [AIRBAG SENSOR,SIDE]
• Satellite, front door [AIRBAG SENSOR,FRT DOOR]
• Satellite, driver's/front passenger seat
• Satellite, vehicle centre [MODULE, AIRBAG CONTROL]
Cables and plugs:
• Check cables and connectors for damage, replace if necessary
Seat belt system:
• Automatic reel
• Belt buckle tensioner
• Seat belt height adjustment
• End fitting pretensioner
Seats:
• Seat
• Airbag module
• Active head restraint
Driver's airbag:
• Airbag module
• Steering Wheel
• Steering column
Front-passenger airbag:
• Airbag module
• Dashboard trim panel (must be replaced with vehicles without
replaceable airbag cover!)
• Supporting tube
Head airbag:
• Airbag module
• Trim, A-pillar
• Roofliner
• Trim, B-pillar
• Trim, C-pillar
• Connection/mount (on side frame)
Passive knee protector:
• Trim panels (driver's side) [BOLSTER,KNEE]
• Glovebox incl. knee protector (passenger side) [BOLSTER,KNEE]
Check components; replace if necessary
Important!
Only repair those cables which show visible signs of damage. In the event of visible damage, make sure there is only one cable repair in effect after the repair work. If no visible damage can be identified, the entire cable must be replaced. When carrying out repairs to the airbag wiring harness, you must use the spare parts offered in the out Electronic Parts Catalogue (EPC).
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.
