OEM Restraints System Part Replacement Search
2016 Nissan Juke
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
WARNING:To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
1. Turn the ignition switch off.
2. Disconnect negative battery terminal.
3. Wait at least 3 minutes.
After the work is completed, Conduct self-diagnosis using CONSULT-III and “AIR BAG” warning lamp
REV: 12/2016
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
FOR FRONTAL COLLISION : When SRS has deployed in a collision:• If the driver air bag [AIRBAG,STEERING WHEEL] has deployed: REPLACE Install with new fasteners.
• If the front passenger air bag [AIRBAG,INSTRUMENT PNL] has deployed: REPLACE Install with new fasteners
• If any of the front air bags or seat belt pre-tensioners• have been activated: REPLACE the crash zone sensor [AIRBAG SENSOR,FRONT] and bracket with new fasteners
• If the Driver seat belt pretensioner (All applicable locations: buckle, retractor, lap outer) has been activated: REPLACE seat belt pre-tensioner assembly with new fasteners
• If the Passenger seat belt pretensioner (All applicable locations: buckle, retractor, lap outer) has been activated: REPLACE seat belt pre-tensioner assembly with new fasteners
• Confirm seat belt pre-tensioner activation using CONSULT only
• If any of the SRS components have been activated: REPLACE the diagnosis sensor unit [MODULE, AIRBAG CONTROL] Install with new fasteners.
• If the driver front airbag has deployed: REPLACE the spiral cable. [CLOCK SPRING]
• If the passenger air bag has deployed: REPLACE the instrument panel assembly. (integrated type)
• Never use the old fixing nuts after removal, replace with the new nuts
FOR SIDE AND ROLLOVER COLLISION: When SRS has deployed in a collision:
• If the side curtain air bag [AIRBAG,ROOF] LH has deployed: REPLACE the side curtain air bag module LH Install with new fasteners.
• If the side curtain air bag [AIRBAG,ROOF] RH has deployed: REPLACE the side curtain air bag module RH Install with new fasteners.
• If either the front LH or front RH side air bag modules has been deployed: REPLACE front seatback assembly on the deployed side and the deployed seat airbag module [AIRBAG,FRONT SEAT].
• If any of the SRS components have deployed: REPLACE the (satellite) sensor [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE] on the collision side with new fasteners
• If any of the SRS components have been activated: REPLACE the diagnosis sensor unit [MODULE, AIRBAG CONTROL] with new fasteners.
• Driver or passenger seat belt pretensioner has been activated: REPLACE seat belt pre-tensioner assembly with new fasteners
• Passenger seat belt pretensioner has been activated: REPLACE seat belt pre-tensioner assembly with new fasteners
• Confirm seat belt pre-tensioner activation using CONSULT only
NISSAN/INFINITI recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly.
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)Perform self-diagnosis using CONSULT or air bag warning lamp
For a front air bag deployment:
• Steering wheel
• Spiral cable
• Crash zone sensor
• Non-deployed airbags
• Steering wheel harness, connectors and terminals
• Wiring harness, connectors and terminals
• Instrument panel assembly
• All seat belt assemblies including retractors and attaching hardware
• If any component of seat belt assembly is questionable, do not repair. Replace the entire seat belt assembly
• Seats and seat mounting points
• Occupant classification system
(Passenger seat)
• Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
For a side air bag deployment:
• Non-deployed airbags
• Side air bag (satellite) sensor
(LH or RH)
• Trim/headliner
• Center inner pillar on the collision side for damage (dents, cracks, deformation), repair if damaged
• Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side
• Seats and seat mounting points
• All seat belt assemblies including retractors and attaching hardware
• If any component of seat belt assembly is questionable, do not repair. Replace the entire seat belt assembly
• Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
Inspect all seat belt assemblies including retractors and attaching hardware after any collision. NISSAN/INFINITI recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and buckles show no damage and continue to operate properly).
• The seat belt was damaged in an accident (i.e., torn webbing, bent retractor or guide, etc.).
• The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The seat belt pre-tensioners should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
