OEM Restraints System Part Replacement Search
2011 Ford Mustang
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Warning! To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag SRS components and before servicing, replacing, adjusting, or striking components near the front or side air bag sensors or RCM, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.1. Turn all vehicle accessories OFF.
2. Turn the ignition switch to OFF.
3. At the Smart Junction Box (SJB), located in the RH lower kick panel, remove the cover and the RCM fuse 31 (10A) from the SJB. For additional information, refer to the Wiring Diagram Manual.
4. Turn the ignition ON and visually monitor the air bag indicator for at least 30 seconds. The air bag indicator will remain lit continuously (no flashing) if the correct RCM fuse has been removed. If the airbag indicator does not remain lit continuously, remove the correct RCM fuse before proceeding.
5. Turn the ignition OFF.
6. Disconnect the battery ground cable(s). Be sure to disconnect auxiliary batteries and power supplies (if equipped).
7. Wait at least 1 minute.
REV: 11/2012
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When any deployable device or combination of devices have deployed and/or the Restraints Control Module (RCM) has DTC B1231/B1193:00 (Event Threshold Exceeded) in memory, the repair of the vehicle SRS is to include the removal of all deployed devices and the installation of new deployable devices, the removal and installation of new impact sensors and the removal and installation of a new RCM.Removal of all deployed devices and the installation of new deployable devices: [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL; AIRBAG,FRONT SEAT]
Removal and installation of new impact sensors and the removal and installation of a new RCM: [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,SIDE; MODULE,AIRBAG CONTROL]
When the driver air bag module has deployed, a new clockspring must be installed.
If a side air bag deployment took place, install a new seat backrest foam pad, cover, side air bag module, bracket, nuts, U-nuts, bolts and seat backrest frame (if necessary).
New driver safety belt systems (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the driver safety belt pretensioners.
New front passenger safety belt systems (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the Passenger safety belt pretensioners.
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
When a vehicle has been involved in a collision and the occupant classification system module (OCSM) has DTC B1231 stored in memory, the repair of the OCS system is to include the following procedures for the specified system: For bladder-type OCS system, inspect for damage and repair as necessary. If installation of an OCS system component is required, an OCS system service kit must be installed.When any damage to the impact sensor mounting points or mounting hardware has occurred, repair or install new mounting points and mounting hardware as needed.
Inspect the entire vehicle for damage, including the following components:
• Steering column (deployable column if equipped)
• Instrument panel knee bolsters and mounting points
• Instrument panel braces and brackets
• Instrument panel and mounting points
• Seats and seat mounting points
• Safety belts, safety belt buckles, safety belt retractors and safety belt anchors.
• SRS wiring, wiring harnesses and connectors
Before installing a new safety belt assembly, the safety belt attaching areas must be inspected for damage and distortion. If the attaching points are damaged and distorted, the sheet metal must be worked back to its original shape and structural integrity
After carrying out the review and inspection of the entire vehicle for damage, repair or install new components as needed
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
