OEM Restraints System Part Replacement Search


2020 Nissan TITAN XD CREW CAB

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN dealer.

1. Turn the ignition switch off.
2. Disconnect the battery or batteries
3. Wait at least 3 minutes.

REV: 03/2021

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

FOR FRONTAL COLLISION : When SRS has deployed in a collision:

• If the driver airbag has deployed: REPLACE Install with new fasteners. [AIRBAG,STEERING WHEEL]
• If the front passenger airbag has deployed: REPLACE Install with new fasteners. [AIRBAG,INSTRUMENT PNL]
• If any of the front air bags or seat belt pretensioners• have been activated: REPLACE the crash zone sensor and bracket with new fasteners [AIRBAG SENSOR,FRONT]
• If either the driver or passenger seat belt pre-tensioner• (All applicable locations: buckle, retractor, lap outer) has been activated: REPLACE the seat belt pre-tensioner assembly with new fasteners. Confirm seat belt pre-tensioner activation using CONSULT only
• If any of the SRS components have been activated: REPLACE the diagnosis sensor unit. Install with new fasteners. [MODULE,AIRBAG CONTROL]
• If the driver front air bag has deployed: REPLACE the spiral cable [CLOCK SPRING]
• If the passenger front air bag has deployed: REPLACE the instrument panel assembly. (integrated type)

FOR SIDE AND ROLLOVER COLLISION: When SRS has deployed:

• If the LH side curtain air bag has deployed: REPLACE the LH side curtain air bag module [AIRBAG,ROOF]
• If the RH side curtain air bag has deployed: REPLACE the RH side curtain air bag module [AIRBAG,ROOF]
• If the front side air bag LH has deployed: REPLACE front seatback assembly LH [AIRBAG & SEAT BACK ASSY]
• If the front side air bag RH has deployed: REPLACE front seatback assembly RH [AIRBAG & SEAT BACK ASSY]
• If any of the SRS components have deployed: REPLACE the side airbag (satellite) sensor on the collision side with new fasteners. [AIRBAG SENSOR,SIDE, ART & RR]
• If any of the SRS components have deployed: REPLACE the diagnosis sensor unit with new fasteners [MODULE,AIRBAG CONTROL]
• If either the driver or passenger seat belt pre-tensioner• (All applicable locations: buckle, retractor, lap outer) has been activated: REPLACE the seatbelt pre-tensioner assembly with new fasteners. Confirm seat belt pre-tensioner activation using CONSULT only

Replace any seat belt assembly (including anchor bolts) if the seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and buckles show no damage and continue to operate properly)

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

FOR FRONTAL COLLISION : When SRS has deployed in a collision:
• Steering wheel
• Steering wheel harness, connectors and terminals
• Non-deployed airbags
• Harness and connectors
• Occupant classification system (Passenger seat)
• Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
• If any component of seat belt assembly is questionable, do not repair. Replace the entire seat belt assembly

FOR SIDE AND ROLLOVER COLLISION: When SRS has deployed in a collision:
• Non-deployed airbags
• Center inner pillar on the collision side for damage (dents, cracks, deformation), repair if damaged
• Trim/headliner • Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the collision side
• If any component of seat belt assembly is questionable, do not repair. Replace the entire seat belt assembly
• Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

• Inspect all seat belt assemblies including retractors and attached hardware after any collision. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly.

Replace any seat belt assembly (including anchor bolts) if:
• The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and buckles show no damage and continue to operate properly).
• The seat belt was damaged in an accident (i.e. torn webbing, bent retractor or guide).
• The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses