OEM Restraints System Part Replacement Search


2020 Lincoln MKZ Hybrid

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

Warning! To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag SRS components and before servicing, replacing, adjusting, or striking components near the front or side air bag sensors or RCM, such as doors, instrument panel, console, door latches, strikers, seats and hood latches. To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).

1. Turn the ignition switch to OFF.
2. At the BCM, located under the instrument panel, to the left of the steering column, remove BECM fuse 14 (10A) and 35 (5A) from the BCM. Refer to Wiring Cell 11 Fuse and Relay Information for schematic and connector information.
3. Turn the ignition ON and monitor the airbag warning indicator for at least 30 seconds. The airbag warning indicator remains lit continuously (no flashing) if the correct RCM fuse is removed. If the airbag warning indicator is not lit continuously, remove the correct RCM fuse before proceeding.
4. Turn the ignition OFF.
5. Disconnect the battery ground cable. Be sure to disconnect auxiliary batteries and power supplies (if equipped).
6. Wait at least one minute before continuing vehicle service.

REV: 04/2020

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

When any deployable device or combination of devices have deployed and/or the RCM has DTC B1193:00 (event threshold exceeded) in memory, the repair of the vehicle SRS is to include the removal of all deployed devices and the installation of new deployable devices, the removal and installation of new impact sensors and the removal and installation of a new RCM:

Removal of all deployed devices and the installation of new deployable devices: [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL; AIRBAG,KNEE BOLSTER; AIRBAG,FRONT SEAT; AIRBAG,ROOF; AIRBAG,SEATBELT [if equipped]]

Removal and installation of new impact sensors and the removal and installation of a new RCM: [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,QTR PANEL; MODULE,AIRBAG CONTROL]

When the driver airbag has deployed, install a new clockspring.

Install new safety belt(s) at any seating position(s) where deployment has occurred and the safety belt(s) were used

New driver safety belt systems (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the driver safety belt pretensioners.

New front passenger safety belt systems (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the front passenger safety belt pretensioners.

New second row safety belt systems (including retractors, buckles and inflators) must be installed if the vehicle is involved in a collision that results in deployment of the rear inflatable safety belt system. [AIRBAG,SEATBELT]

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

When a vehicle has been involved in a collision and the OCSM has DTC B1193:00 stored in memory, the repair of the OCS is to include the following procedures for the
specified system:
• For a weight sensor bolt-type OCS , inspect the passenger side floorpan for damage and repair as necessary. Install a new seat track with OCS weight sensor bolts. The
DTC must be cleared from the OCSM before carrying out OCS Reset. Do not install a new OCSM unless DTC B1193:00 cannot be cleared.
• For a bladder-type OCS , inspect for damage and repair as necessary. If installation of an OCS component is required, an OCS service kit must be installed.

When any damage to the impact sensor mounting points or mounting hardware has occurred, repair or install new mounting points and mounting hardware as needed

Inspect the entire vehicle for damage, including the following components:
• Steering column (deployable column if equipped)
• Instrument panel knee bolsters and mounting points
• Safety Canopy and mounting points
• Instrument panel braces and brackets
• Instrument panel and mounting points
• Seats and seat mounting points
• Safety belts, safety belt buckles and safety belt retractors
• SRS wiring, wiring harnesses and connectors

Safety belt assembly attaching areas must be inspected. Damaged or distorted attaching areas must be restored to their original structural integrity and a new safety belt assembly with new attaching hardware must be installed.

Before installing a Safety Canopy or side air curtain module, inspect the roofline for any damage. If necessary, the sheet metal must be reworked to its original condition and structural integrity.

Inspect the fuel system for damage or leaks. Repair the system and install new components as necessary

Connect a diagnostic scan tool and view the BCM CRASH PID.

After carrying out the review and inspection of the entire vehicle for damage, repair or install new components as needed

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses