OEM Restraints System Part Replacement Search
2016 Ram Ram Promaster
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
To avoid potential physical injury or damage to sensitive electronic circuits and systems,always disconnect and isolate the battery negative (ground) cable and the positive cable,
then ground the positive cable to discharge the Occupant Restraint Controller (ORC) capacitor
before performing any welding operations on the vehicle
1. Disconnect and isolate the battery negative (ground) cable.
2. Wait two minutes for the system capacitor to discharge before further system service.
REV: 03/2024
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
Any vehicle which is to be returned to use following a Supplemental Restraint System (SRS) component deployment must have the deployed restraints replaced.If the driver airbag is deployed:
• Driver AirBag (DAB) [AIRBAG,STEERING WHEEL]
• Clockspring [CLOCK SPRING/LVR,STRG]
• Steering column
• Both front seat belt anchor buckle tensioners
• Both outboard front seat belt retractor and tensioner assemblies
• Any front seat belt buckle or retractor in use must be replaced
If the passenger airbag is deployed:
• Passenger AirBag (PAB) [AIRBAG,INSTRUMENT PNL]
• PAB door
• The PAB wire harness or connector and the instrument panel must be replaced
If a seat airbag is deployed:
• Seat AirBag (SAB) (also known as pelvic and thoracic airbags) [AIRBAG,FRONT SEAT]
• Seat back frame
• Seat back foam
• Seat back trim cover on the same side of the vehicle as the deployed airbag must also be replaced.
• Side impact sensors on the same side of the vehicle as the deployed airbag
• Both front seat belt anchor buckle tensioners
• Both outboard front seat belt retractor and tensioner assemblies
• Any front seat belt buckle or retractor in use must be replaced
If a seat belt tensioner is deployed:
• All seat belt tensioners must be replaced if any airbag in the vehicle has been deployed.
If a side curtain airbag is deployed:
• Side curtain airbag (also known as Side AirBag Inflatable Curtain/SABIC) [AIRBAG,ROOF]
• Headliner
• Upper A and B-pillar trim on the same side of the vehicle as the deployed airbag
• The impact sensors on the same side of the vehicle as the deployed airbag
• Both front seat belt anchor buckle tensioners
• Both outboard front seat belt retractor and tensioner assemblies
• Any front seat belt buckle or retractor in use must be replaced
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Following ANY major vehicle impact damage in the vicinity of an impact sensor or the ORC • It is critical that the mounting surfaces and mounting brackets for the Occupant Restraint Controller (ORC), front impact sensors and side impact sensors located within the proximity of the impact damage be closely inspected and restored to their original conditions. [MODULE,AIRBAG CONTROL; AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE]• Following ANY airbag deployment event • All interior trim panels must be inspected
If the driver airbag is deployed:
• The front impact sensors and the steering wheel must be inspected
If a side curtain airbag is deployed:
• The A-pillar reinforcement on the roof inner side rail and the deploy bracket on the B-pillar for the same side of the vehicle as the deployed airbag must be closely inspected following a side curtain airbag deployment
The components identified with the deployed SRS components in the preceding list are not intended for reuse and will be damaged or weakened as a result of an airbag deployment, which may or may not be obvious during a visual inspection.
All other vehicle components should be closely inspected following any SRS component deployment, but are to be replaced only as required by the extent of the visible damage incurred.
There are two methods by which an airbag or seat belt tensioner may be connected to the vehicle electrical system:
• The first method involves a short pigtail harness and connector insulator that are integral to the airbag or tensioner unit and are replaced as a unit with the service replacement airbag or seat belt tensioner. This connection method typically requires no additional wiring repair following a deployment.
• The second connection method involves a wire harness takeout and connector insulator that are connected directly to the airbag or tensioner initiator or squib. These direct-connect type take outs and connector insulators MUST be repaired following an airbag or seat belt tensioner deployment using the approved Supplemental Restraint System Wiring Repairs procedure. (Refer to 10 • Restraints • Standard Procedure).
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
