OEM Restraints System Part Replacement Search
2016 Scion iM
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Check for DTCs before disconnecting the cable from the negative (-) battery terminal1. Turn ignition switch to OFF and remove key.
2. Disconnect and isolate negative battery cable.
3. Wait at least 90 seconds.
• Before using an electric welder on the vehicle, remove any SRS parts around the area being repaired.
• Before repairs, remove the airbag sensor assemblies if impacts are likely to be applied to the sensor during repairs
REV: 09/2015
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When the SRS parts are deployed (including when only an airbag or pretensioner is deployed) due to a collision, be sure to replace all sensors in the damaged areas (anywhere in need of repair) and the airbag sensor assembly (center airbag sensor assembly):• Steering wheel pad,[AIRBAG, STEERING WHEEL], [if deployed]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER], [if deployed]
• Instrument panel passenger airbag assembly, [AIRBAG, INSTRUMENT PNL], [if deployed]
• Curtain shield airbag assembly, [AIRBAG,ROOF], [if deployed]
• Front seat airbag assemblies, [AIRBAG,FRONT SEAT], [if deployed]
• Front seat cushion airbag assembly [AIRBAG,FRT SEAT CUSHION]
• Airbag sensor assembly center, [MODULE, AIRBAG CONTROL]
Replace all sensors in the damaged areas (anywhere in need of repair):
• [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
• If the front seat cushion airbag assembly RH has been deployed, replace the front seat cushion airbag assembly RH, front seat adjuster assembly RH, separate type front seat cushion pad and separate type front seat cushion cover with the necessary parts in accordance with the extent of the collision damage
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• Horn button assembly [AIRBAG,STEERING WHEEL]• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assemblies [AIRBAG,FRONT SEAT]
• Front seat cushion airbag assembly [AIRBAG,FRT SEAT CUSHION]
• Front seat outer belt assemblies
Visually check the airbag sensors in undamaged areas for defects:
• Front airbag sensors
• Door side airbag sensors
• Side airbag sensors
• Rear airbag sensors
• Front pillar garnish
• Roof headlining
• SRS wire harness or connector
• If any of the SRS parts are dropped, or if any cracks, dents or other defects are found, replace them with new parts
When the airbag sensor assembly (center airbag sensor assembly) is replaced
• perform zero point learning for the yaw rate and acceleration sensor
• perform initialization
Replace any faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, tether anchor hardware and other related parts). When inspecting a vehicle that has been involved in a collision, be sure to check all of the seat belt systems regardless of whether or not the ELR function of the system was activated in the collision. Replace any damaged or malfunctioning parts of the systems.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
