OEM Restraints System Part Replacement Search
2015 Lexus NX
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
HYBRID:1) Turn off power switch
2) Disconnect the negative (-) auxiliary battery terminal
3) Wait at least 90 seconds
ALL OTHERS:
1) Turn off engine switch
2) Disconnect the negative (-) battery terminal
3) Wait at least 90 seconds
REV: 04/2015
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When airbags have deployed as the result of a collision, be sure to replace sensors in the damaged areas (anywhere in need of repair) and the airbag ECU assembly [MODULE,AIRBAG CONTROL; AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,QTR PANEL][Deployed Airbags]
• Driver's Airbag, [AIRBAG,STEERING WHEEL; AIRBAG,KNEE BOLSTER]
• Front passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Side seat airbag [AIRBAG,FRONT SEAT BACK]
• Cushion airbag [AIRBAG,FRT SEAT CUSHION]
• Curtain shield airbag assembly [AIRBAG,ROOF]
• If the side seat airbag was deployed, replace the front seat airbag assembly, front seatback frame subassembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage
• If the cushion airbag was deployed, replace the front seat airbag sub-assembly RH, separate type front seat cushion spring assembly, separate type front seat cushion cover and separate type front seat cushion pad with the necessary parts in accordance with the extent of the collision damage
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
When troubleshooting the SRS, always inspect DTCs before disconnecting the battery.• Horn button assembly [AIRBAG,STEERING WHEEL]
• Instrument panel passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag [AIRBAG,ROOF]
• Front seat airbag assembly [AIRBAG & SEAT ASSY,FRT (Canada Built); AIRBAG,FRONT SEAT (Japan Built)]
• Lower No. 1 instrument panel airbag [AIRBAG,KNEE BOLSTER]
• Front seat outer belt assembly
• Front seat cushion airbag assembly RH [AIRBAG,FRT SEAT CUSHION]
• Rear No. 1 seat outer belt assembly
• Front seat inner belt assembly
• Airbag ECU assembly [MODULE,AIRBAG CONTROL]
• Front airbag sensor [AIRBAG SENSOR,FRONT]
• Door side airbag sensor [AIRBAG SENSOR,FRT DOOR]
• Side airbag sensor [AIRBAG SENSOR,QTR PANEL]
• Seat position airbag sensor
• Occupant detection ECU
• Steering wheel
• Instrument panel or Instrument panel reinforcement
• Front pillar garnish and Headliner
• OCS: Perform zero point calibration and sensitivity check
• As the SRS parts are very hot after being deployed, ensure that all wire harnesses and connectors around deployed SRS parts are not damaged.
Be sure to perform initialization of the occupant detection ECU under any of the following conditions. If initialization is not performed, the SRS may not operate properly:
a. The occupant detection ECU is replaced.
b. Accessories (seatback tray, seat cover, etc.) are installed to the vehicle.
c. The passenger seat is removed from the vehicle, and then reinstalled or replaced.
d. The passenger airbag ON/OFF indicator light (OFF) comes on when the passenger seat is not occupied.
e. The vehicle is brought to a workshop for repair due to an accident or collision.
Replace the faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, adjustable shoulder anchor, tether anchor hardware and other related parts). When inspecting a vehicle that was in a collision, be sure to check all of the seat belt systems regardless of whether or not the system was activated in the collision. Replace any damaged or malfunctioning systems
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
