OEM Restraints System Part Replacement Search
2014 Acura TL
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before doing any SRS repairs, Check for DTCs with the HDS for the less obvious deployed components (front seat belt tensioners, front impact sensors, side impact sensors, rear safing sensor, etc.).Make sure you have the anti-theft code(s) for the audio system and/or the audio-navigation system (if equipped).
Before disconnecting the SRS unit connectors, always disconnect the appropriate SRS parts connectors.
1. Always turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
2. Disconnect and isolate the negative cable from the battery.
3. Wait at least 3 minutes before starting work
REV: 02/2014
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a collision where the seat belt tensioners deployed, replace these items:• SRS unit [MODULE,AIRBAG CONTROL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]
After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed front airbag(s) [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]
• Dashboard (deployed front passenger's airbag)
After a collision where a side airbag deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Seat frame and related parts, for the side that Deployed. If the seat-back cover is split, it must be replaced.
• Front seat belt(s)
After a collision where a side curtain airbag has deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Front seat belt(s)
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor [AIRBAG SENSOR,INTERIOR]
• A-pillar trim
• B-pillar upper trim
• C-pillar trim
• Front grab handle
• Rear grab handle
• All related trim clips
• Sunvisor
• Headliner
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• Inspect all the SRS wire harnesses. Replace, do not repair, any damaged harnesses• If the harness is broken or damaged in the areas relevant to the replacement (SRS) parts, replace the harness, do not repair it.
• Before doing any SRS repairs, Check for DTCs with the HDS for the less obvious deployed components (front seat belt tensioners, front impact sensors, side impact sensors, rear safing sensor).
• Do not replace the ODS unit unless it is physically damaged or a specific fault was found during DTC troubleshooting because it could complicate troubleshooting other DTCs.
• After a vehicle collision, do the ODS unit operation check
• After a vehicle collision, inspect the front seat active head restraints
• Inspect the cable reel for heat damage. If there is any damage, replace the cable reel [CLOCK SPRING]
• Seats and seat mounting points
• Seatbelts and seatbelt mounting points
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. If the airbag is frayed, or has any other visible damage, replace it. Do not attempt to repair an airbag. If the clips are stress-whitened, replace them with new ones.
• Front Passenger's Weight Sensor Output Check After a Vehicle Collision inspection procedure
• Replace all damaged parts.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
