OEM Restraints System Part Replacement Search
2013 Subaru Impreza
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
1. Turn the ignition switch to OFF.2. Disconnect the ground cable from the battery.
3. Wait for more than 60 seconds or more before starting work.
REV: 12/2013
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
Replace the following parts if the airbag has been activated.1. FRONT COLLISION
1) Driver’s airbag module [AIRBAG,STEERING WHEEL]
2) Passenger’s airbag module [AIRBAG,INSTRUMENT PNL]
3) Driver’s seat belt (pretensioner)
4) Passenger’s seat belt (pretensioner)
5) Airbag control module [MODULE,AIRBAG CONTROL]
6) Front sub sensor [AIRBAG SENSOR,FENDER]
7) Roll connector [CLOCK SPRING]
8) Passenger’s side seat cushion pad and frame assembly
9) Instrument panel (for integrating with passenger’s airbag module)
2. SIDE COLLISION
1) Airbag control module [MODULE,AIRBAG CONTROL]
2) Satellite safing sensor [AIRBAG SENSOR,FLOOR MTD]
3) Satellite safing sensor cover [AIRBAG SENSOR,COVER]
4) Side airbag module (operating side seat backrest) [AIRBAG,FRONT SEAT]
5) Side airbag sensor (operating side) [AIRBAG SENSOR,SIDE]
6) Curtain airbag module (operating side) [AIRBAG,ROOF]
7) Curtain airbag sensor (operating side) [AIRBAG SENSOR,QTR PANEL]
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Check for the following parts, and replace the damaged parts with new parts.• Steering wheel and steering shaft
• Check the direct type connector of driver’s airbag module, curtain airbag module, pretensioner, etc. for damage, and also check each harness for pinch and connector damage. Replace the main harness as a unit if damage is found.
• Check the seat cushion, backrest, seat rail and headrest for installing condition and play.
• Combination switch
• Steering roll connector
• For the passenger’s seat:
• Replace the seat cushion pad frame assembly with a new part if the seat cushion frame assembly is deformed or cracked.
• Seat belt buckle body or bracket is scratched, cracked or deformed
• Backrest frame for crack or deformation
• Headrest for deformation or play
• If the seat cushion cover and seat backrest cover is scratched or coming loose, replace with a new cover and readjust the system.
• If there are tears or loosening in the passenger side seat cushion cover, it may interfere with the proper operation of the passenger detection system. Replace with a new cushion cover.
• Be sure to perform the system calibration for the occupant detection system after removing or replacing the passenger seat cushion cover
• Use the Subaru Select Monitor to check whether the front right seat belt buckle switch is operating normally
• Driver’s airbag module/ Harness and/or connector
• Passenger’s airbag module and mounting bracket/ Harness and/or connector
• Front seat, airbag module and mounting bracket/ Harness and/or connector
• Curtain airbag module and mounting bracket/ Harness and/or connector
Inspect impact sensors and connector/ mounting brackets in damaged areas and replace the damaged parts with new parts:
• Front sub sensor [AIRBAG SENSOR,FENDER]
• Satellite safing sensor and cover
• Side airbag sensor
• Curtain airbag sensor
With side collision (when side airbag is activated), check for the following, and replace damaged parts with new parts:
• Backrest pad assembly
• Backrest frame assembly
• Backrest cover assembly
• when damage is found by visual check:
• Headrest assembly
• Headrest lock bushing
• Outer slide rail
• Inner slide rail
• Seat hinge cover
• Seat lifter lever
• Reclining lever
• Side airbag harness and connector on body side
• Satellite safing sensor cover
With side collision (when curtain airbag is activated), check for the following, and replace the damaged parts with new parts:
• Roof trim
• Front pillar upper trim
• Center pillar upper trim
• Rear quarter pillar trim
• Airbag guide
• Airbag bracket (model with sunroof)
• When damage is found by visual check:
• Assist grip
• Assist grip bracket
• Curtain airbag harness and connector on body side.
• Satellite safing sensor cover
SYSTEM CALIBRATION (REZEROING), OPERATION, Subaru Select Monitor.> CAUTION:
If any of the following applies, replace the seat cushion pad and frame assembly. Do not disassemble.
• Cracks or deformation found in the seat cushion frame or seat cushion pad.
• Scratches, cracks, or deformation found on the passenger detection system pressure sensor hoses or passenger detection control module, or attachment brackets of the control
module.
• Harness and/or connector is cracked, deformed or open. Harness wire is exposed
• After checking the installing condition of passenger’s seat, perform the system calibration of occupant detection system.
• Check the Belt tension sensor and harness and/or connector for scratches, cracks, or deformation.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
