OEM Restraints System Part Replacement Search
2013 Honda Accord Sedan
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before disconnecting the SRS unit connectors, always disconnect the appropriate SRS parts connectors.1. Always turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode
2. Disconnect the negative cable from the battery
3. Wait at least 3 minutes before starting work
REV: 08/2016
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a collision where the front seat belt tensioners deployed, replace these items:• SRS unit [MODULE,AIRBAG CONTROL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]
After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed front airbag(s) [AIRBAG, STEERING WHEEL; AIRBAG, INSTRUMENT PNL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]
• Dashboard (deployed front passenger's airbag)
After a collision where the side airbag deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor (USA and Canada models) [AIRBAG SENSOR,INTERIOR]
• B-pillar lower trim
• Seat frame and related parts
• After a collision where the side airbag was deployed, replace the side airbag and the seat frame with the new parts. If the seat-back cover is split, it must be replaced
After a collision where the side curtain airbag deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Front seat belt(s)
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor (USA and Canada models) [AIRBAG SENSOR,INTERIOR]
• A-pillar trim
• B-pillar upper trim
• C-pillar trim
• Front grab handle
• Rear grab handle
• All related trim clips
• Sunvisor
• Headliner
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• If the harness is broken or damaged in the areas relevant to the replacement parts, replace the harness, do not repair it.• Before doing any SRS repairs, check for DTCs with the HDS, for the less obvious deployed components (front seat belt tensioners, front impact sensors, side impact sensors, etc.).
• USA and Canada models: Do not replace the front passenger's weight sensor unit unless it is physically damaged or a specific fault was found during DTC troubleshooting because it could complicate troubleshooting other DTCs.
• USA and Canada models: After a vehicle collision, do the front passenger's weight sensor unit operation check.
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. Replace the components as needed.
• Never attempt to modify, splice, or repair SRS wiring. If there is an open or damage to the SRS wiring, replace the harness.
• Replace all damaged parts
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
