OEM Restraints System Part Replacement Search
2012 Acura TSX Sport Wagon
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before doing any SRS repairs, check for DTCs with the HDS for the less obvious deployed components (front seat belt tensioners, front impact sensors, side impact sensors, rear safing sensor, etc).Before disconnecting the SRS unit connectors, always disconnect the appropriate SRS parts connectors.
1. Make sure the ignition switch is in LOCK (0), or the vehicle ignition in the OFF mode.
2. Disconnect and isolate the negative cable from the battery.
NOTE: Always disconnect the negative cable from the battery first.
3. Disconnect the positive cable from the battery.
4. Wait at least 3 minutes before starting work
REV: 05/2014
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a collision where the seat belt tensioners deployed, replace these items:• SRS unit [MODULE,AIRBAG CONTROL]
• Front seat belt(s)
• Front impact sensor(s)
After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed front airbag(s) [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]
• Dashboard
After a collision where the side airbag has deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Side impact sensor(s) (first) [AIRBAG SENSOR,INTERIOR]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• B-pillar lower trim
• Seat frame and related parts. If the seat-back cover is split, it must be replaced
• Front seat belt(s)
After a collision where a side curtain airbag has deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Front seat belt(s)
• Side impact sensor(s) (first) [AIRBAG SENSOR,INTERIOR]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor [AIRBAG SENSOR,INTERIOR]
• Roof trim (Headliner)
• A-pillar trim
• B-pillar upper trim
• C-pillar trim (Sedan)
• Quarter pillar trim (Sport Wagon)
• Front grab handle
• Rear grab handle
• All related trim clips
• Sunvisor
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• If there is a breaking or damage found in harness relevant to the replacement parts, replace it, do not repair.• Before doing any SRS repairs, check for DTCs with the HDS for the less obvious deployed components (front seat belt tensioners, front impact sensors, side impact sensors, rear safing sensor, etc).
• Do not replace the ODS unit unless it is physically damaged or a specific fault was found during DTC troubleshooting. Because it could complicate troubleshooting other DTCs
• After a vehicle collision, do the ODS unit operation check.
• After a vehicle collision, inspect the front seat active head restraints.
• Inspect all the SRS wire harnesses
• If the cable reel shows any signs of damage, replace it with a new one [CLOCK SPRING]
• Front Passenger's Weight Sensor Output Check After a Vehicle Collision
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. Replace the components as needed.
• Replace all damaged parts.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
