OEM Restraints System Part Replacement Search
2011 Lexus RX 350
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before using an electric welder on the vehicle, remove any SRS parts around the area being repaired.1. Turn ignition switch to LOCK and remove key.
2. Disconnect and isolate negative battery cable.
3. Wait 90 seconds.
REV: 03/2013
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When the SRS parts are deployed (including when only an airbag or pretensioner is deployed) due to a collision, be sure to replace all sensors in the damaged areas (anywhere in need of repair) and center airbag sensor assembly. [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL; MODULE,AIRBAG CONTROL][Deployed airbags]
• Steering wheel pad [AIRBAG, STEERING WHEEL]
• Driver side knee airbag assembly, [AIRBAG,KNEE BOLSTER]
• Front passenger side knee airbag assembly, [AIRBAG,KNEE BOLSTER]
• Front passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assembly, [AIRBAG,ROOF]
• Rear seat side airbag [AIRBAG & SEAT ASSY,RR]
TMC made • If the front seat side airbag assembly was deployed, replace the front seat side airbag assembly, front seat frame assembly with adjuster, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.
• [AIRBAG,FRONT SEAT]
TMMC MAde
• Front seat airbag assembly, [AIRBAG & SEAT ASSY,FRT]
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Perform a diagnostic system checkEven in the case of a minor collision when the SRS does not deploy inspect the following. If a defect is found (e.g. cracks, dents or any other defects) in any of the housings, brackets or connectors, then replace the part with a new one:
• Spiral cable [CLOCK SPRING]
• Steering Pad [AIRBAG, STEERING WHEEL]
• Front Passenger Airbag Assembly [AIRBAG,INSTRUMENT PNL]
• Driver Side Knee Airbag Assembly [AIRBAG,KNEE BOLSTER]
• Passenger Side Knee Airbag Assembly [AIRBAG,KNEE BOLSTER]
• Front Seat Airbag Assembly
• Rear Seat Airbag Assembly
• Curtain Shield Airbag Assembly [AIRBAG,ROOF]
• Center Airbag Sensor Assembly [MODULE,AIRBAG CONTROL]
• Front Airbag Sensor [AIRBAG SENSOR,FRONT]
• Front Seat Inner Belt Assembly
• Seat Position Sensor
• Occupant Classification ECU
• Occupant Classification system: Perform zero point calibration and sensitivity check
• Side Airbag Sensor [AIRBAG SENSOR,SIDE]
• Side Airbag Sensor [AIRBAG SENSOR,FRT DOOR]
• Rear Airbag Sensor [AIRBAG SENSOR,QTR PANEL]
• Front Seat Outer Belt Assembly
Replace any faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, adjustable shoulder anchor, tether anchor hardware and other related parts). When inspecting a vehicle that was in a collision, be sure to check all of the seat belt systems regardless of whether or not the system was activated in the collision. Replace any damaged or malfunctioning systems
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
