OEM Restraints System Part Replacement Search
2008 Land Rover LR2
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before working on or in the vicinity of SRS components, make sure the system is rendered safe by performing the followingoperations:
1) Remove the remote control.
2) Disconnect battery, earth lead first. Always disconnect both battery cables before beginning work on the SRS system. Disconnect the ground cable first. Never reverse connect the battery.
3) Wait 2 minutes for the SRS power circuit to discharge before commencing work
REV: 02/2015
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
Front Airbag Deployment • Driver and PassengerCAUTION: If the front airbags are deployed, the following components must be replaced:
• Driver airbag module [AIRBAG,STEERING WHEEL; AIRBAG,KNEE BOLSTER]
• Steering wheel
• Passenger airbag module [AIRBAG,INSTRUMENT PNL]
• Instrument panel
• Fly leads (where applicable) connecting front airbag modules to SRS harness
• All seat belt buckle pre-tensioner
• All occupied seats at the time of the crash should have their seat belts replaced
• Any seat belt with a deployed retractor pretensioner should be replaced.
• Rotary coupler [CLOCK SPRING]
• Any front impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRONT]
• RCM [MODULE,AIRBAG CONTROL]
Side Air Bags
CAUTION: If the side (thorax) air bags are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side (thorax) airbag [AIRBAG,FRONT SEAT]
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• RCM [MODULE,AIRBAG CONTROL]
Side Curtain Airbag Modules
CAUTION: If the head airbag modules are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side curtain airbag modules [AIRBAG,ROOF]
• Headliner and all pillar trims
• Link lead between airbag gas generator and RCM harness
• Airbag retaining clips
• Front seat belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• RCM [MODULE,AIRBAG CONTROL]
Rear impacts
If the seat belt pre-tensioners are deployed during a rear impact, the following components must be replaced:
• Seat belt pre-tensioners
• Front and rear seat belt retractors used during the impact
• RCM [MODULE,AIRBAG CONTROL]
Always use new fixings when replacing an SRS component and make sure that all fixings are tightened to the correct torque.
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Check for structural damage in the area of impact paying particular attention to bumper armatures, longitudinals and bracketry.The SRS side impact sensor must be replaced if there are any signs of physical damage or if the RCM is registering a fault.
The restraints control module (RCM) must be replaced after every time any SRS component has been deployed.
Front Airbag Deployment • Driver and Passenger, the following items must be inspected for damage and replaced as necessary:
• Front passenger's seat belt retractor and webbing, tongue latching function, 'D' loop and body anchorage point
• Rear seat belt buckles, webbing, buckle covers, body anchorage points and tongue latching function
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse
• Seat belt height adjusters
• Rear seat belts
Side Air Bags, the following items must be inspected for damage and replaced as necessary:
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Seat belt height adjusters
• Rear seat belts
Side Curtain Airbag Modules, the following items must be inspected for damage and replaced as necessary:
• Component mounting brackets
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Adjacent trim components
• Seat belt height adjusters
Rear impacts, the following items must be inspected for damage and replaced as necessary:
• Seat belt height adjusters
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
| Additional Information |
Please select a Make, Model and/or Year
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
