OEM Restraints System Part Replacement Search
2024 Land Rover Range Rover
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before working on or in the vicinity of SRS components, make sure the system is rendered safe by performing the following operations:1. Remove the ignition key.
2. Disconnect the battery, earth lead first.
3. Wait 2 minutes for the SRS power circuit to discharge before commencing work.
REV: 04/2024
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
The replacement and inspection policy is dependent on the type and severity of the crash condition. The following guidelines are the minimum that should be exercised as a result of the deployment of specific SRS components:Always use new fixings when replacing an SRS component
If the front air bags are deployed, the following components must be replaced:
• Driver air bag module, if deployed [AIRBAG,STEERING WHEEL]
• Steering wheel
• Passenger air bag module, if deployed [AIRBAG,INSTRUMENT PNL]
• Instrument panel
• Fly leads (where applicable) connecting front air bag modules to SRS harness
• All seat belt buckle pre-tensioner
• All occupied seats at the time of the crash should have their seat belts replaced
• Any seat belt with a deployed retractor pretensioner should be replaced.
• Rotary coupler [CLOCK SPRING]
• Any front impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRONT]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the side (thorax) air bags are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side (thorax) airbag, if deployed [AIRBAG,FRONT SEAT]
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,QTR PANEL]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the head airbag modules are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side curtain airbag modules [AIRBAG,ROOF]
• Headliner and all pillar trims
• Link lead between airbag gas generator and RCM harness
• Airbag retaining clips
• Front seat belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,QTR PANEL]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the safety belt pre-tensioners are deployed during a rear impact, the following components must be replaced:
• Safety belt pre-tensioners
• Front and rear safety belt retractors deployed during the impact
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
Always replace a safety belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying.
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• Check for structural damage in the area of impact paying particular attention to bumper armatures, longitudinals and bracketry.• Always replace a seat belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying.
• Always use new fixings when replacing an SRS component
If the front air bags are deployed, the following items must be inspected for damage and replaced as necessary:
• Front passenger safety belt retractor and webbing, tongue latching function, 'D' loop and body anchorage point
• Rear safety belt buckles, webbing, buckle covers, body anchorage points and tongue latching function
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse
• Seat belt height adjusters
• Rear seat belts
If the Side (thorax) airbag [AIRBAG,FRONT SEAT] are deployed, the following items must be inspected for damage and replaced as necessary:
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Seat belt height adjusters
• Rear seat belts
If the Head airbag modules [AIRBAG,ROOF] are deployed, the following items must be inspected for damage and replaced as necessary:
• Component mounting brackets
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Adjacent trim components
• Safety belt height adjusters
If the seat belt pre-tensioners are deployed during a rear impact, the following items must be inspected for damage and replaced as necessary:
• Safety belt height adjusters
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
Never attempt to modify, splice or repair SRS wiring
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.
