OEM Restraints System Part Replacement Search
2007 Honda Element
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before removing any SRS parts (including disconnection of connectors), always disconnect the SRS connector.1. Make sure the ignition switch is in LOCK (0)
2. Disconnect the negative cable from the battery
3. Wait at least 3 minutes before starting work
REV: 04/2011
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a collision where the front seat belt tensioners deployed, replace these items:• SRS unit [MODULE,AIRBAG CONTROL]
• Front seat belt(s)
• Front seat belt buckle tensioner(s)
• Front impact sensor(s) [AIRBAG SENSOR,FENDER]
After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed front airbag(s) [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL]
• Front seat belt(s)
• Front seat belt buckle tensioner(s)
• Front impact sensor(s) [AIRBAG SENSOR,FENDER]
After a collision where the side airbag deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,SIDE]
• C-pillar lower trim
• All related trim clips
• Side airbag module holder
• Seat frame and related parts
After a collision where the side curtain airbag has deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Front seat belt(s)
• Front seat belt buckle tensioner(s)
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,SIDE]
• Roll rate sensor [AIRBAG SENSOR,INTERIOR]
• Rear safing sensor [AIRBAG SENSOR,INTERIOR]
• Roof trim
• A-pillar trim
• Rear roof trim
• Upper quarter window trim
• D-pillar trim
• Front grab handle
• Rear grab handle
• All related trim clips
• Sunvisor
• Any damaged restraint system part
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• Before doing any SRS repairs, use the HDS SRS Menu Method to check for DTCs; refer to the DTC Troubleshooting Index for the less obvious deployed parts (front seat belt tensioners, front impact sensors, side impact sensors, etc.).• Do not replace the ODS unit unless it is physically damaged or a specific fault was found during DTC troubleshooting. Because it could complicate troubleshooting other DTCs.
• After a vehicle collision, do the ODS unit operation check.
• Check the front passenger's weight sensor output after a vehicle collision
• After a collision where the side airbag was deployed, if the seat-back cover is split, it must be replaced. Do not repair a torn or frayed seat-back cover. Replace the seat-back cover if it is damaged.
During the repair process, inspect these areas:
• Inspect all the SRS wire harnesses. Replace, do not repair, any damaged harnesses.
• Inspect the cable reel for heat damage. If there is any damage, replace the cable reel. [CLOCK SPRING]
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. Replace the components as needed.
• Any restraint system part or wiring identified by diagnostic check
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.
