OEM Restraints System Part Replacement Search


2007 Land Rover Range Rover

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

1. Remove the ignition key.
2. Disconnect battery, negative lead first.
3. Wait 10 minutes before commencing work.

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

Safety belt pre-tensioner deployment:
• Safety belt pre-tensioners
• Front and rear safety belt retractors deployed during the impact
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part (brackets and fixings) or wiring identified by diagnostic check

For front airbag deployment:
• Driver airbag module (if deployed)
• Passenger airbag module if deployed)
• Flyleads (where applicable) connecting front airbag modules to SRS harness
• Front safety belt buckle pre-tensioner
• Rear safety belt pre-tensioners • if installed
• Driver safety belt retractor • if installed
• Clockspring (rotary coupler)
• Any front impact sensors that have been physically damaged or if a fault is being registered
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check

For a knee airbag deployment:
• Knee airbag if deployed)
• Both side impact sensors
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check

For a side airbag deployment:
• Side air curtains (front side airbags) if deployed)
• Any side impact sensors that have been physically damaged or if a fault is being registered
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check


For a side air curtain module deployment:
• Side air curtain modules (roof airbag) if deployed)
• Link lead between side air curtain gas generator and restraints control module (RCM) harness
• Side air curtain module retaining clips
• Internal trim finisher
• Front safety belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

Safety belt pre-tensioner deployment:
• Safety belt height adjusters
• Front safety belts, retractors and webbing, tongue latching function, and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check

For a front airbag deployment:
• Front passenger safety belt retractor and webbing, tongue latching function, 'D' loop, body anchorage point
• Rear safety seat buckles • webbing, buckle covers, tongue latching function, body anchorage points
• Instrument panel moulding adjacent to passenger air bag module
• Steering wheel
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse, replace
• Safety belt height adjusters
• Rear safety belts
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check

For a side airbag deployment:
• Front safety belts, retractors, webbing, tongue latching function, 'D' loop, body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Safety belt height adjusters
• Rear safety belts
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check

For a side air curtain module deployment:
• Headlining
• Component mounting brackets
• Front safety belts, retractors, webbing, tongue latching function, 'D' loop, body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function and body anchorage points
• Adjacent trim components
• Safety belt height adjusters
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses