OEM Restraints System Part Replacement Search
2007 Acura TSX
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Turn the ignition switch OFF and disconnect the negative cable from the battery, and wait at least 3 minutes before beginning the following procedures.Before disconnecting SRS unit connector from the SRS unit, disconnect both seat belt tensioner 4P connectors.
Before disconnecting the cable reel 4P connector, disconnect driver's airbag 4P connector.
Before removing any of the SRS parts (including disconnection of the connectors), always disconnect SRS connector.
1. Disconnect the battery negative cable, and wait at least 3 minutes.
Driver's Airbag:
2. Remove the access panel from the steering wheel, then disconnect the driver's airbag 4P connector from the cable reel.
Front Passenger's Airbag:
3. Remove the glove box, and the glove box housing then disconnect the front passenger's airbag 4P connector from the dashboard wire harness.
Side Airbag:
4. Disconnect the side airbag 2P connector from the floor wire harness.
Side Curtain Airbag:
5. Disconnect the side curtain airbag 2P connector from the side curtain airbag subharness.
Seat Belt Tensioner:
6. Disconnect the seat belt tensioner 4P connector from the floor wire harness.
SRS Unit:
7. Disconnect SRS unit connector(s) from the SRS unit.
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a seat belt tensioner deployment:• SRS unit [Module, Airbag Control]
• Seat belt tensioners
• Front impact sensors [Airbag Sensor, Fender and/or Airbag Sensor, Interior]
• Seat belts in use during collision
• Any damaged restraint system part [Airbag Brkt, Interior and/or Airbag Module, Interior and/or Cover, Pass Airbag]
After a front airbag(s) deployment:
• SRS unit [Airbag Control Module]
• Deployed airbag(s) [Steering Wheel Airbag and/or Instrument Pnl Airbag]
• Seat belt tensioners
• Front impact sensors [Fender Airbag Sensor and/or Interior Airbag Sensor]
• Seat belts in use during collision
• Any damaged restraint system part [Airbag Brkt, Interior and/or Airbag Module, Interior and/or Cover, Pass Airbag]
After a side airbag(s) deployment:
• SRS unit [Module, Airbag Control]
• Deployed side airbag(s) [Airbag, Front Seat]
• Side impact sensor(s) [Airbag Sensor, Fender and/or Airbag Sensor, Qtr Panel and/or Airbag Snsr, Active Weight and/or Airbag Sensor, Interior] (first) for the side(s) that deployed
• Seat-back cover
• Seat belts in use during collision
• Any damaged restraint system part [Airbag Brkt, Interior and/or Airbag Module, Interior]
After a side curtain airbag(s) deployment:
• SRS unit [Module, Airbag Control]
• Deployed side curtain airbag(s) [Airbag, Roof]
• Side impact sensor(s) [Airbag Sensor, Fender and/or Airbag Sensor, Qtr Panel and/or Airbag Snsr, Active Weight and/or Airbag Sensor, Interior] (first) for the side(s) that deployed
• Side impact sensor(s) [Airbag Sensor, Fender and/or Airbag Sensor, Qtr Panel and/or Airbag Snsr, Active Weight and/or Airbag Sensor, Interior] (second) for the side(s) that deployed
• Roof trim
• A pillar trim
• B pillar trim
• C pillar trim
• Front grab handle
• Sunvisor
• Any related trim clips
• All trim clips on that side (where a side curtain airbag has deployed), even if they appear to be undamaged.
• Seat belts in use during collision
• Any damaged restraint system part [Airbag Brkt, Interior and/or Airbag Module, Interior]
After a side curtain airbag deployment, replace the clips on these parts even if they look undamaged:
• Front pillar trim
• Center pillar trim
• Rear pillar trim
• Front grab handle
• Sunvisor
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• All the SRS wire harnesses [Airbag Harness, Interior]• Cable reel [Clock Spring]
• Side impact sensors [Airbag Sensor, Fender and/or Airbag Sensor, Qtr Panel and/or Airbag Snsr, Active Weight and/or Airbag Sensor, Interior]
• Any restraint system part or wiring identified by diagnostic check
For a side airbag deployment:
• All the SRS wire harnesses [Airbag Harness, Interior]
• Seat-back cushion
• Seat-back frame
• Front impact sensors [Airbag Sensor, Fender and/or Airbag Sensor, Qtr Panel and/or Airbag Snsr, Active Weight and/or Airbag Sensor, Interior]
• Any restraint system part or wiring identified by diagnostic check
For a side curtain airbag deployment:
• All the SRS wire harnesses [Airbag Harness, Interior]
• Front impact sensors [Airbag Sensor, Fender and/or Airbag Sensor, Qtr Panel and/or Airbag Snsr, Active Weight and/or Airbag Sensor, Interior]
• Any restraint system part or wiring identified by diagnostic check
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.
