OEM Restraints System Part Replacement Search


2007 Honda Accord Coupe

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

1) Turn the ignition switch OFF
2) Disconnect the negative cable from the battery
3) Wait at least 3 minutes before beginning work

• Before removing any of the SRS parts (including the disconnection of the connectors), always disconnect the SRS connector

REV: 02/2011

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

After a collision where the seat belt tensioners deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Seat belt tensioners
• Front impact sensors [AIRBAG SENSOR,FENDER]

After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed airbag(s)
[AIRBAG,STEERING WHEEL], if deployed
[AIRBAG,INSTRUMENT PNL], if deployed
• Seat belt tensioners
• Front impact sensors [AIRBAG SENSOR,FENDER]

After a collision where the side airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Seat belt tensioner(s) for the side(s) that deployed
• Side impact sensor(s) (first) for the side(s) that deployed [AIRBAG SENSOR,INTERIOR]
• Side impact sensor(s) (second) for the side(s) that deployed (4-door) [AIRBAG SENSOR,QTR PANEL]

After a collision where the side curtain airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Seat belt tensioner(s) for the side(s) that deployed
• Side impact sensor(s) (first) for the side(s) that deployed [AIRBAG SENSOR,INTERIOR]
• Side impact sensor(s) (second) for the side(s) that deployed (4-door) [AIRBAG SENSOR,QTR PANEL]
• Roof trim (Headliner)
• A-pillar trim
• B-pillar trim
• C-pillar trim
• Front grab handle
• Sunvisor
• All related trim clips

After a collision, where a side curtain airbag has deployed, replace all trim clips on that side, even if they appear to be undamaged. Replace the clips on these
parts:
• A-pillar trim
• B-pillar trim
• C-pillar trim
• Front grab handle
• Sunvisor
• Any damaged restraint system part

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

• Before doing any SRS repairs, use the HDS SRS menu method to check for DTCs; read the DTC for the less obvious deployed parts (seat belt tensioners, front impact sensors, side airbag sensors, etc.)
• Do not mix TRW and Denso impact sensors. Impact sensors and the SRS unit must be of the same manufacturer
• After a moderate to severe side or rear collision, inspect for damage on the side curtain airbag or other related components. According to the degree of damage, replace components as needed
• Inspect all the SRS wire harnesses. Replace, don't repair, any damaged harnesses.
• Inspect the cable reel for heat damage. If there is any damage, replace the cable reel
• After a collision in which the side airbag was deployed, inspect the seat-back cushion and the seatback
frame. If the seat-back cushion is split, it must be replaced. If the seatback frame is deformed, it must be replaced.
• Any damaged restraint system part

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses