OEM Restraints System Part Replacement Search


2021 Toyota Highlander

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

Before using an electric welder on the vehicle, remove any SRS parts around the area being repaired.
Before repairs, remove the airbag sensor assemblies if impacts are likely to be applied to the sensor during repairs

1. Turn ignition switch to OFF and remove key.
2. Disconnect and isolate negative battery cable.
3. Wait at least 90 seconds.

REV: 01/2024

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

When the SRS parts are deployed (including when only an airbag or pretensioner is deployed) due to a collision, be sure to replace all sensors in the damaged areas (anywhere in need of repair) and airbag sensor assembly (center airbag sensor assembly). [AIRBAG SENSOR,FRONT, AIRBAG SENSOR,FRT DOOR, AIRBAG SENSOR,SIDE, AIRBAG SENSOR,QTR PANEL, MODULE,AIRBAG CONTROL]

[Replace deployed airbags]
• Horn button assembly [AIRBAG,STEERING WHEEL]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger without door airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assemblies [AIRBAG,FRONT SEAT]
• Front seat cushion airbag assembly RH
• Front seat outer belt assembly
• Rear seat outer belt assembly
• Airbag sensor assembly [MODULE,AIRBAG CONTROL]
• Front airbag sensors [AIRBAG SENSOR,FRONT]
• Door side airbag sensors [AIRBAG SENSOR,FRT DOOR]
• Side airbag sensor assemblies [AIRBAG SENSOR,SIDE]
• Rear airbag sensors [AIRBAG SENSOR,QTR PANEL]

• Replace any faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, adjustable shoulder anchor
, tether anchor hardware and other related parts). When inspecting a vehicle that was in a collision, be sure to check all of the seat belt systems regardless of whether or not the system was activated in the collision. Replace any damaged or malfunctioning systems.

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

Always check for DTCs before disconnecting the cable from the negative (-) battery terminal.
Visually check the airbag sensors in undamaged areas for defects.
If any defects are found or an airbag sensor has detected a major collision, replace the airbag sensor with a new one.

• Airbag sensor assembly [MODULE,AIRBAG CONTROL]
• Front airbag sensors [AIRBAG SENSOR,FRONT]
• Door side airbag sensors [AIRBAG SENSOR,FRT DOOR]
• Side airbag sensor assemblies [AIRBAG SENSOR,SIDE]
• Rear airbag sensors [AIRBAG SENSOR,QTR PANEL]
• Horn button assembly [AIRBAG,STEERING WHEEL]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger without door airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assembly [AIRBAG,FRONT SEAT]
• Front seat cushion airbag assembly RH
• Front seat inner belt assembly
• Front seat outer belt assembly
• Rear seat outer belt assembly

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses