OEM Restraints System Part Replacement Search


2020 Land Rover Range Rover Sport PHEV

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

A minimum period of two minutes must have elapsed from the ignition being switched to the 'OFF' position prior to disconnection of the battery.

1. Remove the ignition key.
2. Disconnect the battery, earth lead first.
3. It is essential that a period of 10 minutes elapses after the battery is disconnected before any work is undertaken on any part of the SRS

REV: 07/2020

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

The replacement and inspection policy is dependent on the type and severity of the crash condition. The following guidelines are the minimum that should be exercised as a result of the deployment of specific SRS components:

Always use new fixings when replacing an SRS component

If the front air bags are deployed, the following components must be replaced:
• Driver air bag module [AIRBAG,STEERING WHEEL]
• Passenger air bag module [AIRBAG,INSTRUMENT PNL]
• Fly leads (where applicable) connecting front air bag modules to SRS harness
• Front safety belt buckle pre-tensioner
• Rear safety belt pre-tensioners • if installed
• Driver safety belt retractor • if installed
• Clockspring [CLOCK SPRING]
• Any front impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRONT]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

If the side air curtains are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side air curtains
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,ART DOOR, AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

If the side air curtain modules [AIRBAG,ROOF] are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side air curtain modules [AIRBAG,ROOF]
• Link lead between side air cuirtain gas generator and restrains control module (RCM) harness
• Side air curtain module retaning clips
• Internal trim finisher
• Front safety belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,ART DOOR, AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restrains Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

Rear impacts
If the safety belt pre-tensioners are deployed during a rear impact, the following components must be replaced:
• Safety belt pre-tensioners
• Front and rear safety belt retractors deployed during the impact
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

Always replace a safety belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying.

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

• Check for structural damage in the area of impact paying particular attention to bumper armatures, longitudinals and bracketry.
• Always replace a seat belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying.
• Always use new fixings when replacing an SRS component

If the front air bags are deployed, the following items must be inspected for damage and replaced as necessary:
• Front passenger safety belt retractor and webbing, tongue latching function, 'D' loop and body anchorage point
• Rear safety belt buckles, webbing, buckle covers, body anchorage points and tongue latching function
• Instrument panel moulding adjacent to passenger air bag module
• Steering wheel
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse
• Safety belt height adjusters
• Rear safety belts

If the side air curtains are deployed, the following items must be inspected for damage and replaced as necessary:
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Safety belt height adjusters
• Rear safety belts

If the side air curtain modules [AIRBAG,ROOF] are deployed, the following items must be inspected for damage and replaced as necessary:
• Headlining
• Component mounting brackets
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Adjacent trim components
• Safety belt height adjusters

If the seat belt pre-tensioners are deployed during a rear impact, the following items must be inspected for damage and replaced as necessary:
• Safety belt height adjusters
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points

Never attempt to modify, splice or repair SRS wiring

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses