OEM Restraints System Part Replacement Search


2020 Lexus ES

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

Before using an electric welder on the vehicle, remove any SRS parts around the area being repaired.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. See the navigation note below.

1. Turn ignition switch to OFF
2. Disconnect the cable from the negative (-) battery terminal.
3. Wait at least 90 seconds.

When the cable is disconnected from the negative (-) battery terminal, the memory of various systems will be cleared. Because of this, be sure to make a record of the contents memorized in each system before starting work. When work is finished, adjust each system to its previous state.

REV: 01/2021

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

When the SRS parts are deployed (including when only an airbag or pretensioner is deployed) due to a collision, be sure to replace all sensors in the damaged areas (anywhere in need of repair) and airbag sensor assembly (center airbag sensor). [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL; MODULE,AIRBAG CONTROL]

Deployed airbag(s):

• Horn button assembly [AIRBAG, STEERING WHEEL]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Lower No. 2 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assemblies [AIRBAG,FRONT SEAT BACK]
• Rear seat airbag assemblies [AIRBAG,REAR SEAT]



PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

Visually check the airbag sensors in undamaged areas for defects.
If any defects are found or an airbag sensor has detected a major collision, replace the airbag sensor with a new one.

• Horn button assembly [AIRBAG, STEERING WHEEL]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Lower No. 2 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assemblies [AIRBAG,FRONT SEAT BACK]
• Rear seat airbag assemblies [AIRBAG,REAR SEAT]
• Front seat outer belt assemblies
• Rear seat outer belt assemblies
• Airbag sensor assembly[MODULE,AIRBAG CONTROL]
• Front airbag sensors [AIRBAG SENSOR,FRONT]
• Door side airbag sensors [AIRBAG SENSOR,FRT DOOR]
• Side No. 1 airbag sensors [AIRBAG SENSOR,SIDE]
• Side No. 2 airbag sensor assemblies [AIRBAG SENSOR,QTR PANEL]

Occupant Classification precaution:
• Perform zero point calibration and sensitivity check

Replace any faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, adjustable shoulder anchor, tether anchor hardware and other related parts). When inspecting a vehicle that was in a collision, be sure to check all of the seat belt systems regardless of whether or not the system was activated in the collision. Replace any damaged or malfunctioning systems.

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses