OEM Restraints System Part Replacement Search


2020 Jaguar I-PACE

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

1. Remove the ignition key.
2. Disconnect battery, earth lead first.
3. Wait 2 minutes for the SRS power circuit to discharge before commencing work

REV: 10/2019

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

If the front airbags are deployed, the following components must be replaced:
• Driver airbag module [AIRBAG,STEERING WHEEL]
• Passenger airbag module [AIRBAG,INSTRUMENT PNL]
• Fly leads (where applicable) connecting front airbag modules to SRS harness
• Front seat belt buckle pre-tensioner
• Rear seat belt pre-tensioners • if installed
• Driver's seat belt retractor • if installed
• Rotary coupler [CLOCK SPRING/LVR,STRG]
• Any front impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRONT]
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

If the side (thorax) air bags are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side (thorax) airbag [AIRBAG,FRONT SEAT]
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

If the head airbag modules are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Head airbag modules [AIRBAG,ROOF]
• Link lead between airbag gas generator and restraints control module (RCM) harness
• Airbag retaining clips
• Internal trim finisher
• Front seat belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

If the seat belt pre-tensioners are deployed during a rear impact, the following components must be replaced:
• Seat belt pre-tensioners
• Front and rear seat belt retractors used during the impact
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]

The Restraints Control Module (RCM) will log a crash fault after every impact which is severe enough to cause airbag deployment. It is possible to have three
crashes/impacts logged after one event where, for example, a front, side and rollover has occurred. After the third fault is logged, the SRS warning lamp will be
illuminated and the RCM must be installed. After any airbag deployment a new RCM must be installed [MODULE,AIRBAG CONTROL]

The SRS side impact sensor must be replaced if there are any signs of physical damage or if the restraints control module (RCM) is registering a fault [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]

Always replace a seat belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

If the front airbags are deployed • Additionally, the following items must be inspected for damage and replaced as necessary:
• Front passenger's seat belt retractor and webbing, tongue latching function, 'D' loop and body anchorage point
• Rear seat belt buckles, webbing, buckle covers, body anchorage points and tongue latching function
• Fascia moulding adjacent to passenger airbag module
• Steering wheel
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse
• Seat belt height adjusters
• Rear seat belts

If the side (thorax) air bags are deployed • Additionally, the following items must be inspected for damage and replaced as necessary:
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Seat belt height adjusters
• Rear seat belts

If the side (thorax) air bags are deployed • Additionally, the following items must be inspected for damage and replaced as necessary:
• Headlining
• Component mounting brackets
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Adjacent trim components
• Seat belt height adjusters

If the seat belt pre-tensioners are deployed during a rear impact • Additionally, the following items must be inspected for damage and replaced as necessary:
• Seat belt height adjusters
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses