OEM Restraints System Part Replacement Search


2010 INFINITI G37/Q60 Convertible

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance should be performed by an authorized NISSAN/INFINITI dealer.

1. Turn the ignition switch OFF.
2. Disconnect both battery cables.
3. Wait at least 3 minutes.

REV: 03/2013

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

FOR FRONTAL COLLISION:
• If the driver air bag has deployed: REPLACE Install with new fasteners. [AIRBAG,STEERING WHEEL]
• If the front passenger air bag has deployed: REPLACE Install with new fasteners. [AIRBAG,INSTRUMENT PNL]
• If any of the front air bags or seat belt pre-tensioners have been activated: REPLACE the crash zone sensor and bracket with new fasteners. [AIRBAG SENSOR,FRONT]
• Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer) [if deployed]
• If any of the SRS components have been activated: REPLACE the diagnosis sensor unit. Install with new fasteners [MODULE,AIRBAG CONTROL]
• If the driver front air bag has deployed: REPLACE the spiral cable. [CLOCK SPRING]
• If the passenger air bag has deployed: REPLACE the instrument panel assembly. (integrated type)
• Always replace instrument panel pad following front passenger air bag deployment

FOR SIDE AND ROLLOVER COLLISION:
• If the side air bag LH has deployed: REPLACE front seatback assembly LH. [AIRBAG,FRONT SEAT]
• If the side air bag RH has deployed: REPLACE front seatback assembly RH. [AIRBAG,FRONT SEAT]
• If the door-mounted curtain air bag module LH has deployed: REPLACE the door finisher LH and door-mounted curtain air bag module. Install with new fasteners. [AIRBAG,FRONT DOOR]
• If the door-mounted curtain air bag module RH has deployed: REPLACE the door finisher RH and door-mounted curtain air bag module. Install with new fasteners. [AIRBAG,FRONT DOOR]
• If any of the SRS components have deployed: REPLACE the satellite sensor on the collision side with new fasteners. [AIRBAG SENSOR,QTR PANEL]
• If the pop-up roll bar has deployed: REPLACE pop-up roll bar assemblies and pop-up roll bar covers. Install with new fasteners [ROLL BAR ASSEMBLY]
• If any of the SRS components have deployed: REPLACE the diagnosis sensor unit with new fasteners. [MODULE,AIRBAG CONTROL]
• Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer) [if deployed]

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks, deformation, etc.)
• Steering wheel
• Airbag Modules that have not deployed
• Steering wheel harness, connectors and terminals
• Wiring harness, connectors and terminals
• Occupant Classification System
• Seats and seat mounting points
• Instrument panel assembly
• Pop-up roll bar
• Inspect all seat belt assemblies including retractors and attaching hardware and mounting points after any collision
• Check for deformities of the center pillar inner
• Replace any seat belt assembly (including anchor bolts) if Seat belt attaching point was damaged in an accident.
• Doors and Door trim
• NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly

*This matrix does not currently contain all production vehicles sold in the United States. The contents were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information.


Related I-CAR Courses