OEM Restraints System Part Replacement Search


2007 Hummer H2 SUT

Print

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
2. Place the ignition in the OFF position
3. Disconnect the negative battery cable from the battery.
4. Wait 1 minute before working on system.

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

• Inflatable restraint I/P module [Airbag, Instrument Pnl], if deployed
• Inflatable restraint steering wheel module [Airbag, Steering Wheel], if deployed
• Inflatable restraint steering wheel module coil [Clock Spring]
• Inflatable restraint sensing and diagnostic module (SDM) [Module, Airbag Control]
• Inflatable restraint electronic frontal sensor (EFS) [Airbag Sensor, Front]
• SIR sensors in area of accident damage, regardless of deployment
• Replace any seat belt system that was in use during a collision serious enough to deploy any automatic restraint device such as air bags and seat belt pretensioners. This not only includes seat belt systems in use by people of adult size, but seat belt systems used to secure child restraints, infant carriers and booster seats, including LATCH system and top tether anchorages.
• Any damaged restraint system part [Airbag Switch, Interior]

With Side Air Bag Deployment :
• Inflatable restraint sensing and diagnostic module (SDM) [Airbag Control Module]
• Inflatable restraint roof rail module [Roof Airbag], on side of impact
• Inflatable restraint side impact sensor (SIS) (front/rear) [Frt Door Airbag Sensor], on side of impact
• Seat belt pretensioner with the buckle, guide and retractor assembly on the side of impact
• SIR sensors [Front Airbag Sensor, Frt Door Airbag Sensor, Floor Mtd Airbag Sensor] in area of accident damage, regardless of deployment or signs of damage. The area of accident damage is defined as the portion
of the vehicle which is crushed, bent, or damaged due to a collision.
• Replace any seat belt system that was in use during the collision serious enough to deploy any automatic restraint device such as air bags and seat belt pretensioners. This not only includes seat belt systems in use by people of adult size, but seat belt systems used to secure child restraints, infant carriers and booster seats, including LATCH system and top tether anchorages.

CAUTION: Restraint systems can be damaged in a collision. To help avoid injury and ensure that all parts in need of replacement are replaced:

Replace any seat belt system that has torn, worn, or damaged components. This not only includes adult seat belt systems, but built-in child restraints and LATCH system components, if any.

Replace any seat belt system if you observe the words "REPLACE" or "CAUTION", or if a yellow tag is visible. Do not replace a seat belt system if only the child seat caution label is visible.

Replace any seat belt system if you are doubtful about its condition. This not only includes adult seat belt systems, but built-in child restraints, LATCH system components, and any restraint system used to secure infant carriers, child restraints and booster seats.

Do NOT replace single seat belt system components in vehicles that have been in a collision as described above. Always replace the entire seat belt system with
the buckle, guide and retractor assembly, which includes the latch and webbing material.

After a minor collision where no automatic restraint device was deployed, seat belt system replacement may not be necessary, unless some of the parts are torn, worn, or otherwise damaged.

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

• Steering column
• Steering wheel module coil and the coil wiring pigtail
• I/P knee bolsters [Bolster, Knee] and mounting points
• I/P brackets, braces, etc.
• Seat belts
• I/P cross car beam [Reinforcement, Instrument Pnl]
• I/P mounting points and brackets
• Seats and seat mounting points
• Steering wheel module coil [Clock Spring] and coil wiring pigtail
• Mounting points and mounting hardware for the I/P module [Airbag, Instrument Pnl], steering wheel module [Airbag, Steering Wheel], SDM [Module, Airbag Control], and EFS sensor [Airbag Sensor, Front]
• Mounting points or mounting hardware for the SIS, roof rail module (left/right)
• Mounting points or mounting hardware for the SDM and vehicle rollover sensor
• Any restraint system part or wiring identified by diagnostic check [Airbag Switch, Interior]




*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses