OEM Calibration Requirements Search
2024 Volkswagen Tiguan
Share:
|
Print
Print
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: Rearview Camera
Calibration/Initialization Requirement Events:
- After an axle alignment
- If camera is removed/installed or replaced
- If front or rear axle or axle components are removed/installed or replaced
- If liftgate handle or latch is removed/installed or replaced
- If repairs are made on the liftgate
| Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Left Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Right Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Driver Assistance Systems Front Camera
Calibration/Initialization Requirement Events:
- If "no or incorrect basic setting/adaptation" is stored in the event memory
- If camera is removed/installed or replaced
- If DTC indicates
- If level control system sensor control position is reprogrammed
- If level control system sensor is readapted on vehicles with damping regulation
- If rear axle toe is adjusted
- If vehicle ride height changes
- If windshield is removed/installed or replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Control Module for Adaptive Cruise Control
Calibration/Initialization Requirement Events:
- If DTC indicates
- If lock carrier is moved into service position
- If lock carrier is removed/installed or replaced
- If rear axle toe is adjusted
- If sensor is removed/installed or replaced
- If vehicle ride height changes
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: Rear Level Control System Sensor
Calibration/Initialization Requirement Events:
- If leveling sensor is removed/installed or replaced
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Parking Aid Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille (Sides)
OEM Name: Front Parallel Parking Assistance Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)
OEM Name: Lane Change Assistance Control Module
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Quarter Panel Behind Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Parking Aid Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover (Sides)
OEM Name: Rear Parallel Parking Assistance Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. The contents are based on OEM vehicle-specific repair information, other OEM-supplied documents available from the vehicle maker, and the I-CAR OEM Linking Pin process. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information. Information displayed in quotes ("") are direct quotes from the OEM-specific/vehicle-specific information and/or the I-CAR OEM Linking Pin process.
