OEM Calibration Requirements Search
2018 Kia Sedona
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate
OEM Name: Back View Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Camera in Deck Lid/Liftgate/Tailgate | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (Middle)
OEM Name: Rear Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
Camera in Deck Lid/Liftgate/Tailgate (Middle) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Left Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
Camera in Side Mirror (Left) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Right Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
Camera in Side Mirror (Right) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Lane Departure Warning System Unit
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If DTC indicates
- If windshield is removed/installed or replaced
Camera Near Rearview Mirror | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
After replacing the camera with a new one, the variant coding procedure must be performed.
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Smart Cruise Control Unit
Calibration/Initialization Requirement Events:
- If radar sensor or the surrounding parts are impacted by a collision
- If sensor does not detect a vehicle in front
- If sensor is removed/installed or replaced
- If steering angle sensor is replaced or adjusted
- If wheel alignment is performed
Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
After replacing the sensor with a new one, the variant coding procedure must be performed.
Sensor(s) Behind Rear Bumper Cover (Sides)
OEM Name: Blind Spot Detection Unit
Calibration/Initialization Requirement Events:
- If DTC indicates
- If sensor or bracket is replaced
- If there is a rear or side collision
Sensor(s) Behind Rear Bumper Cover (Sides) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: Auto Headlamp Leveling Unit
Calibration/Initialization Requirement Events:
- If AHLS ECU is removed/installed or replaced
Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Parking Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Parking Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The contents are based on the repair information available from the vehicle maker. Updates and additions will be posted as they become available. To ensure that the most recent information is used, always refer to the vehicle maker's technical information.