OEM Calibration Requirements Search
2016 Kia Sedona
Print
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate
OEM Name: Back View Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Camera in Deck Lid/Liftgate/Tailgate | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (Middle)
OEM Name: Rear Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
| Camera in Deck Lid/Liftgate/Tailgate (Middle) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Left Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Right Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed or replaced
- If surround view monitoring unit is replaced
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Lane Departure Warning System Unit
Calibration/Initialization Requirement Events:
- If camera is removed or replaced
- If DTC indicates
- If windshield is removed or replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
After replacing the camera with a new one, the variant coding procedure must be performed.
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Smart Cruise Control Unit
Calibration/Initialization Requirement Events:
- If radar sensor or the surrounding parts are impacted by a collision
- If sensor does not detect a vehicle in front
- If sensor is reinstalled or replaced
- If steering angle sensor is replaced or adjusted
- If vehicle was in an accident that required wheel alignment
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Rear Bumper Cover (Sides)
OEM Name: Blind Spot Detection Unit
Calibration/Initialization Requirement Events:
- If DTC indicates
- If sensor or bracket is replaced
- If there is a rear or side collision
| Sensor(s) Behind Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: Auto Headlamp Leveling Unit
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
There is an initialization procedure available for the auto head lamp leveling unit.
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Parking Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Parking Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The contents are based on the repair information available from the vehicle maker. Updates and additions will be posted as they become available. To ensure that the most recent information is used, always refer to the vehicle maker's technical information.
