OEM Calibration Requirements Search
2016 Nissan Maxima
Print
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: Rear View Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is removed
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is removed
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is removed
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is removed
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: ICC Sensor
Calibration/Initialization Requirement Events:
- After any collision to the front of the vehicle that would cause the radar sensor to be shifted or jolted
- If sensor is removed/installed or replaced
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Rear Bumper Cover (Sides)
OEM Name: Side Radar
Calibration/Initialization Requirement Events:
- If any blind spot warning system malfunction is repaired
- If sensor is replaced
| Sensor(s) Behind Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Not a calibration, but an operation check.
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Sonar Sensors
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Sonar Sensors
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. The contents are based on OEM vehicle-specific repair information, other OEM-supplied documents available from the vehicle maker, and the I-CAR OEM Linking Pin process. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information. Information displayed in quotes ("") are direct quotes from the OEM-specific/vehicle-specific information and/or the I-CAR OEM Linking Pin process.
