OEM Calibration Requirements Search
2019 Chrysler Pacifica Hybrid
Print
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: ParkView Rear Back Up Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear Camera
Calibration/Initialization Requirement Events:
- If camera is installed
- If camera mounting location is repaired
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Camera
Calibration/Initialization Requirement Events:
- If camera is installed
- If camera mounting location is repaired
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side Camera
Calibration/Initialization Requirement Events:
- If camera is installed
- If camera mounting location is repaired
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side Camera
Calibration/Initialization Requirement Events:
- If camera is installed
- If camera mounting location is repaired
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera on Rearview Mirror
OEM Name: Forward Facing Camera
Calibration/Initialization Requirement Events:
- If customer brings in a vehicle with lane departure warning (LDW) system behavior concerns
- If FFC is removed or replaced
- If FFC module is removed from the bracket and then reinstalled
- If windshield is replaced
| Camera on Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Rear Bumper Cover
OEM Name: Blind Spot Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) Behind Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Park Assist Sensor (inboard)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille (Lower)
OEM Name: Adaptive Speed Control Sensor
Calibration/Initialization Requirement Events:
- If ACC sensor is removed and reinstalled
- If DTC indicates
- If front end structural repairs are performed
| Sensor(s) in Front Bumper Cover/Grille (Lower) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille (Sides)
OEM Name: Park Assist Sensors (Outboard)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Park Assist Sensor (inboard)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover (Sides)
OEM Name: Park Assist Sensors (Outboard)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. The contents are based on OEM vehicle-specific repair information, other OEM-supplied documents available from the vehicle maker, and the I-CAR OEM Linking Pin process. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information. Information displayed in quotes ("") are direct quotes from the OEM-specific/vehicle-specific information and/or the I-CAR OEM Linking Pin process.
