OEM Calibration Requirements Search
2019 RAM 1500 (DT)
Print
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: ParkVeiw Rear View Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear View Camera
Calibration/Initialization Requirement Events:
- If DTC indicates
- If service is performed on any surround view cameras
- If service is performed on central vision processing module
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front View Camera
Calibration/Initialization Requirement Events:
- If service is performed on any surround view cameras
- If service is performed on central vision processing module
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side View Camera
Calibration/Initialization Requirement Events:
- If service is performed on any surround view cameras
- If service is performed on central vision processing module
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side View Camera
Calibration/Initialization Requirement Events:
- If service is performed on any surround view cameras
- If service is performed on central vision processing module
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Driver Assistance System Module
Calibration/Initialization Requirement Events:
- If DASM is replaced or reinstalled
- If DTC indicates
- If tire diameter changes
- If windshield is replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: (multiple inputs)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Receives input from:
- adaptive front lighting system module (AFLS)
- front and rear axle leveling sensors
- steering angle sensor
- yaw rate sensor
"If this electronic control unit (ECU) is being replaced with a new unit, use a diagnostic scan tool to perform the flash programming procedure (if available)."
Sensor(s) in Additional Location(s) (Sides)
OEM Name: Front Inboard/Outboard Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Additional Location(s) (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Sensors located in fog lamp assembly.
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Center Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Tail Lamp (Sides)
OEM Name: Blind Spot Sensor
Calibration/Initialization Requirement Events:
- If sensor is installed
| Sensor(s) in Tail Lamp (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Near Rearview Mirror
OEM Name: Driver Assistance System Module
Calibration/Initialization Requirement Events:
- If DASM is replaced or reinstalled
- If DTC indicates
- If tire diameter changes
- If windshield is replaced
| Sensor(s) Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. The contents are based on OEM vehicle-specific repair information, other OEM-supplied documents available from the vehicle maker, and the I-CAR OEM Linking Pin process. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information. Information displayed in quotes ("") are direct quotes from the OEM-specific/vehicle-specific information and/or the I-CAR OEM Linking Pin process.
