OEM Calibration Requirements Search
2016 Ford F-150
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: Parking Aid Camera
Calibration/Initialization Requirement Events:
- If camera is replaced
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
May be equipped with pro trailer back up assist, which will require camera alignment.
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
"On vehicles equipped with trailer reverse guidance (TRG), this procedure also perform the trailer reverse guidance camera alignment."
Camera in Front Bumper Cover/Grille (Middle)
OEM Name: Front Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
Camera in Front Bumper Cover/Grille (Middle) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
"On vehicles equipped with trailer reverse guidance (TRG), this procedure also perform the trailer reverse guidance camera alignment."
Camera in Side Mirror (Left)
OEM Name: SIDE PARKING Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
Camera in Side Mirror (Left) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
"On vehicles equipped with trailer reverse guidance (TRG), this procedure also perform the trailer reverse guidance camera alignment."
Camera in Side Mirror (Right)
OEM Name: Side Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
Camera in Side Mirror (Right) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
"On vehicles equipped with trailer reverse guidance (TRG), this procedure also perform the trailer reverse guidance camera alignment."
Camera Near Rearview Mirror
OEM Name: Image Processing Module A
Calibration/Initialization Requirement Events:
- If front air bag is deployed
- If interior mirror is replaced
- If suspension is repaired, aligned, or modified
- If there is a change in the tire size
- If windshield is replaced
Camera Near Rearview Mirror | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
If replacing the camera with a new one, data will typically need to be transferred from existing camera.
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Cruise Control Module
Calibration/Initialization Requirement Events:
- If sensor is removed/installed or replaced
Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
If replacing the sensor with a new one, data will typically need to be transferred from existing sensor.
Sensor(s) in Fender (Sides)
OEM Name: Active Park Assist Sensors
Calibration/Initialization Requirement Events:
- If parking aid sensor is removed
Sensor(s) in Fender (Sides) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Not a calibration, but a required system check.
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Parking Aid Sensor
Calibration/Initialization Requirement Events:
- If parking aid sensor is removed
Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Not a calibration, but a required system check.
Sensor(s) in Tail Lamp (Sides)
OEM Name: Side Obstacle Detection Control Module
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Sensor(s) in Tail Lamp (Sides) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
If replacing the sensor with a new one, data will typically need to be transferred from existing sensor.
Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The contents are based on the repair information available from the vehicle maker. Updates and additions will be posted as they become available. To ensure that the most recent information is used, always refer to the vehicle maker's technical information.