OEM Calibration Requirements Search
2022 RAM 1500 (DT)
Print
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Headliner/Roof
OEM Name: Digital Rearview Mirror Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Headliner/Roof | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera on Rearview Mirror
OEM Name: Drivers Assistance System Module
Calibration/Initialization Requirement Events:
- If drivers assistance system module is removed/installed or replaced
- If DTC indicates
- If tire diameter is changed
- If windshield is removed/installed or replaced
| Camera on Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Per RAM service information: "The interior windshield mounted Drivers Assistance System Module (DASM) includes a camera sensor component and a radar sensor component both housed within a common single module housing"
Sensor(s) in Additional Location(s) (1)
OEM Name: (multiple inputs)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Additional Location(s) (1) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Receives input from:
- steering angle sensor
- vehicle speed sensor
- yaw rate sensor
Sensor(s) in Additional Location(s) (2)
OEM Name: (multiple inputs)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Additional Location(s) (2) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Receives input from:
- steering angle sensor
- turn signal switch
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Center / Inboard Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille (Sides)
OEM Name: Front Outboard Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Tail Lamp (Sides)
OEM Name: Blind Spot Sensor
Calibration/Initialization Requirement Events:
- If DTC indicates
- If sensor is removed/installed or replaced
| Sensor(s) in Tail Lamp (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) on Rearview Mirror
OEM Name: Drivers Assistance System Module
Calibration/Initialization Requirement Events:
- If drivers assistance system module is removed/installed or replaced
- If DTC indicates
- If tire diameter is changed
- If windshield is removed/installed or replaced
| Sensor(s) on Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Per RAM service information: "The interior windshield mounted Drivers Assistance System Module (DASM) includes a camera sensor component and a radar sensor component both housed within a common single module housing"
| Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. The contents are based on OEM vehicle-specific repair information, other OEM-supplied documents available from the vehicle maker, and the I-CAR OEM Linking Pin process. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information. Information displayed in quotes ("") are direct quotes from the OEM-specific/vehicle-specific information and/or the I-CAR OEM Linking Pin process.
