OEM Calibration Requirements Search


2017 Acura MDX

Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.


Vehicle System Options

360° Camera View

Multi View Camera System
Cameras/Sensors:
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
Camera in Front Bumper Cover/Grille
Camera in Side Mirror (Left)
Camera in Side Mirror (Right)
Yes No Not Identified
DTCs Set X
System MIL X



Adaptive Cruise Control

Adaptive Cruise Control
Cameras/Sensors:
Camera Near Rearview Mirror
Sensor(s) Behind Front Bumper Cover/Grille
Yes No Not Identified
DTCs Set X
System MIL X



Collision Warning

Forward Collision Warning / Collision Mitigation Braking
Cameras/Sensors:
Camera Near Rearview Mirror
Sensor(s) Behind Front Bumper Cover/Grille
Yes No Not Identified
DTCs Set X
System MIL X



Collision Braking

Collision Mitigation Braking System
Cameras/Sensors:
Camera Near Rearview Mirror
Sensor(s) Behind Front Bumper Cover/Grille
Yes No Not Identified
DTCs Set X
System MIL X



Blind Spot Detection

Blind Spot Information System
Cameras/Sensors:
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)
Yes No Not Identified
DTCs Set X
System MIL X



Lane Departure Warning

Lane Departure Warning / Road Departure Mitigation
Cameras/Sensors:
Camera Near Rearview Mirror
Yes No Not Identified
DTCs Set X
System MIL X



Lane Keep Assist 1

Lane Keeping Assist System
Cameras/Sensors:
Camera Near Rearview Mirror
Yes No Not Identified
DTCs Set X
System MIL X



Lane Keep Assist 2

Road Departure Mitigation
Cameras/Sensors:
Camera Near Rearview Mirror
Yes No Not Identified
DTCs Set X
System MIL X



Rear View

Rearview Camera System
Cameras/Sensors:
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
Yes No Not Identified
DTCs Set X
System MIL X



Park Assist

Parking And Back-Up Sensor System
Cameras/Sensors:
Sensor(s) in Front Bumper Cover/Grille
Sensor(s) in Rear Bumper Cover
Yes No Not Identified
DTCs Set X
System MIL X



Rear Cross Traffic

Cross Traffic Monitor
Cameras/Sensors:
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)
Yes No Not Identified
DTCs Set X
System MIL X



Adaptive Lighting

Auto High-Beam Support System
Cameras/Sensors:
Camera Near Rearview Mirror
Yes No Not Identified
DTCs Set X
System MIL X




Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)

OEM Name: Multi-View Rear Camera

Calibration/Initialization Requirement Events:

  • No calibration/initialization requirements found
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Systems Affected:

Rear View


Camera in Deck Lid/Liftgate/Tailgate (With 360° View)

OEM Name: Multi View Rear Camera

Calibration/Initialization Requirement Events:

  • If any repairs are made to the driver door
  • If any repairs are made to the front passenger door
  • If driver door is adjusted
  • If driver's door is removed/installed or replaced
  • If DTC indicates
  • If front bumper is removed/installed or replaced
  • If front camera is removed/installed or replaced
  • If front grille is removed/installed or replaced
  • If front passenger door is adjusted
  • If front passenger door is removed/installed or replaced
  • If left side camera is removed/installed or replaced
  • If mirror housing lower cover is removed/installed or replaced
  • If power mirror assembly is removed/installed or replaced
  • If rearview camera is removed/installed or replaced
  • If right side camera is removed/installed or replaced
  • If tailgate is adjusted
  • If tailgate is removed/installed or replaced
  • If trunk is adjusted
  • If trunk is removed/installed or replaced
Camera in Deck Lid/Liftgate/Tailgate (With 360° View) Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."


Systems Affected:

360° Camera View


Camera in Front Bumper Cover/Grille

OEM Name: Multi View Front Camera

Calibration/Initialization Requirement Events:

  • If any repairs are made to the driver door
  • If any repairs are made to the front passenger door
  • If driver door is adjusted
  • If driver's door is removed/installed or replaced
  • If DTC indicates
  • If front bumper is removed/installed or replaced
  • If front camera is removed/installed or replaced
  • If front grille is removed/installed or replaced
  • If front passenger door is adjusted
  • If front passenger door is removed/installed or replaced
  • If left side camera is removed/installed or replaced
  • If mirror housing lower cover is removed/installed or replaced
  • If power mirror assembly is removed/installed or replaced
  • If rearview camera is removed/installed or replaced
  • If right side camera is removed/installed or replaced
  • If tailgate is adjusted
  • If tailgate is removed/installed or replaced
  • If trunk is adjusted
  • If trunk is removed/installed or replaced
Camera in Front Bumper Cover/Grille Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."


Systems Affected:

360° Camera View


Camera in Side Mirror (Left)

OEM Name: Multi View Side Camera

Calibration/Initialization Requirement Events:

  • If any repairs are made to the driver door
  • If any repairs are made to the front passenger door
  • If driver door is adjusted
  • If driver's door is removed/installed or replaced
  • If DTC indicates
  • If front bumper is removed/installed or replaced
  • If front camera is removed/installed or replaced
  • If front grille is removed/installed or replaced
  • If front passenger door is adjusted
  • If front passenger door is removed/installed or replaced
  • If left side camera is removed/installed or replaced
  • If mirror housing lower cover is removed/installed or replaced
  • If power mirror assembly is removed/installed or replaced
  • If rearview camera is removed/installed or replaced
  • If right side camera is removed/installed or replaced
  • If tailgate is adjusted
  • If tailgate is removed/installed or replaced
  • If trunk is adjusted
  • If trunk is removed/installed or replaced
Camera in Side Mirror (Left) Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."


Systems Affected:

360° Camera View


Camera in Side Mirror (Right)

OEM Name: Multi View Side Camera

Calibration/Initialization Requirement Events:

  • If any repairs are made to the driver door
  • If any repairs are made to the front passenger door
  • If driver door is adjusted
  • If driver's door is removed/installed or replaced
  • If DTC indicates
  • If front bumper is removed/installed or replaced
  • If front camera is removed/installed or replaced
  • If front grille is removed/installed or replaced
  • If front passenger door is adjusted
  • If front passenger door is removed/installed or replaced
  • If left side camera is removed/installed or replaced
  • If mirror housing lower cover is removed/installed or replaced
  • If power mirror assembly is removed/installed or replaced
  • If rearview camera is removed/installed or replaced
  • If right side camera is removed/installed or replaced
  • If tailgate is adjusted
  • If tailgate is removed/installed or replaced
  • If trunk is adjusted
  • If trunk is removed/installed or replaced
Camera in Side Mirror (Right) Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."


Systems Affected:

360° Camera View


Camera Near Rearview Mirror

OEM Name: Multipurpose Camera, FCW/LDW Camera, LKAS Camera

Calibration/Initialization Requirement Events:

  • If DTC indicates
  • If multipurpose camera unit is removed/installed or replaced
  • If structural repairs are made
  • If supplemental restraint system (SRS) is deployed
  • If windshield is removed/installed or replaced
Camera Near Rearview Mirror Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Note:
The vehicle may have more than one camera, depending upon ADAS packages. Using a scan tool will identify what camera(s) the vehicle is equipped with.


Systems Affected:

Adaptive Cruise Control Collision Warning Collision Braking Lane Departure Warning Lane Keep Assist 1 Lane Keep Assist 2 Adaptive Lighting


Sensor(s) Behind Front Bumper Cover/Grille

OEM Name: MIllimeter Wave Radar

Calibration/Initialization Requirement Events:

  • If DTC indicates
  • If front bumper cover is repaired within 300 mm of millimeter wave radar unit
  • If millimeter wave radar unit is removed/installed or replaced
  • If structural repairs are made
  • If supplemental restraint system (SRS) is deployed
Sensor(s) Behind Front Bumper Cover/Grille Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Systems Affected:

Adaptive Cruise Control Collision Warning Collision Braking


Sensor(s) in Front Bumper Cover/Grille

OEM Name: Parking and Back-Up Sensor

Calibration/Initialization Requirement Events:

  • If sensor is replaced
  • If sensor mounting location is changed
Sensor(s) in Front Bumper Cover/Grille Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Systems Affected:

Park Assist


Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)

OEM Name: BSI Radar Unit

Calibration/Initialization Requirement Events:

  • If body panel repairs are made near the BSI mounting location
  • If BSI radar unit is removed/installed or replaced
  • If DTC indicates
  • If rear end structural repairs are made
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides) Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Systems Affected:

Blind Spot Detection Rear Cross Traffic


Sensor(s) in Rear Bumper Cover

OEM Name: Parking and Back-Up Sensor

Calibration/Initialization Requirement Events:

  • If sensor is replaced
  • If sensor mounting location is changed
Sensor(s) in Rear Bumper Cover Yes No Not Identified
DTC Set X
Scan Tool Required X
Special Tools Required X

Systems Affected:

Park Assist


Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The contents are based on the repair information available from the vehicle maker. Updates and additions will be posted as they become available. To ensure that the most recent information is used, always refer to the vehicle maker's technical information.


Related I-CAR Courses