OEM Calibration Requirements Search
2023 Acura RDX
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: Multi-View Rear Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Multi View Rear Camera
Calibration/Initialization Requirement Events:
- If driver door is adjusted
- If driver door is removed/installed or replaced
- If driver's door has any repairs made to it
- If DTC indicates
- If front bumper is removed/installed or replaced
- If front camera is removed/installed or replaced
- If front grille is removed/installed or replaced
- If front passenger door has any repairs made to it
- If front passenger door is adjusted
- If front passenger door is removed/installed or replaced
- If left side camera is removed/installed or replaced
- If mirror housing lower cover is removed/installed or replaced
- If power mirror assembly is removed/installed or replaced
- If rearview camera is removed/installed or replaced
- If tailgate is adjusted
- If tailgate is removed/installed or replaced
- If trunk is adjusted
- If trunk is removed/installed or replaced
Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."
Camera in Front Bumper Cover/Grille
OEM Name: Multi View Front Camera
Calibration/Initialization Requirement Events:
- If driver door is adjusted
- If driver door is removed/installed or replaced
- If driver's door has any repairs made to it
- If DTC indicates
- If front bumper is removed/installed or replaced
- If front camera is removed/installed or replaced
- If front grille is removed/installed or replaced
- If front passenger door has any repairs made to it
- If front passenger door is adjusted
- If front passenger door is removed/installed or replaced
- If left side camera is removed/installed or replaced
- If mirror housing lower cover is removed/installed or replaced
- If power mirror assembly is removed/installed or replaced
- If rearview camera is removed/installed or replaced
- If tailgate is adjusted
- If tailgate is removed/installed or replaced
- If trunk is adjusted
- If trunk is removed/installed or replaced
Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."
Camera in Side Mirror (Left)
OEM Name: Multi View Side Camera
Calibration/Initialization Requirement Events:
- If driver door is adjusted
- If driver door is removed/installed or replaced
- If driver's door has any repairs made to it
- If DTC indicates
- If front bumper is removed/installed or replaced
- If front camera is removed/installed or replaced
- If front grille is removed/installed or replaced
- If front passenger door has any repairs made to it
- If front passenger door is adjusted
- If front passenger door is removed/installed or replaced
- If left side camera is removed/installed or replaced
- If mirror housing lower cover is removed/installed or replaced
- If power mirror assembly is removed/installed or replaced
- If rearview camera is removed/installed or replaced
- If tailgate is adjusted
- If tailgate is removed/installed or replaced
- If trunk is adjusted
- If trunk is removed/installed or replaced
Camera in Side Mirror (Left) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."
Camera in Side Mirror (Right)
OEM Name: Multi View Side Camera
Calibration/Initialization Requirement Events:
- If driver door is adjusted
- If driver door is removed/installed or replaced
- If driver's door has any repairs made to it
- If DTC indicates
- If front bumper is removed/installed or replaced
- If front camera is removed/installed or replaced
- If front grille is removed/installed or replaced
- If front passenger door has any repairs made to it
- If front passenger door is adjusted
- If front passenger door is removed/installed or replaced
- If left side camera is removed/installed or replaced
- If mirror housing lower cover is removed/installed or replaced
- If power mirror assembly is removed/installed or replaced
- If rearview camera is removed/installed or replaced
- If tailgate is adjusted
- If tailgate is removed/installed or replaced
- If trunk is adjusted
- If trunk is removed/installed or replaced
Camera in Side Mirror (Right) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Per our contact at Honda: "Cameras can be calibrated in quadrants. You do not need to aim all four unless you have created an event for each camera. Each camera must be calibrated independently."
Camera Near Rearview Mirror
OEM Name: Multipurpose Camera
Calibration/Initialization Requirement Events:
- If DTC indicates
- If multipurpose camera unit is removed/installed or replaced
- If structural repairs are made
- If supplemental restraint system (SRS) is deployed
- If windshield is removed/installed or replaced
Camera Near Rearview Mirror | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Millimeter Wave Radar
Calibration/Initialization Requirement Events:
- If DTC indicates
- If front bumper cover is repaired within 300 mm of millimeter wave radar unit
- If millimeter wave radar unit is removed/installed or replaced
- If structural repairs are made
- If supplemental restraint system (SRS) is deployed
Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: (multiple inputs)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Note:
Receives input from:
- steering angle sensor
- speed sensor
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Parking And Back-Up Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)
OEM Name: BSI Radar Unit
Calibration/Initialization Requirement Events:
- If body panel repairs are made near the BSI mounting location
- If BSI radar unit is removed/installed or replaced
- If DTC indicates
- If rear end structural repairs are made
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides) | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Parking And Back-Up Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
DTC Set | X | ||
Scan Tool Required | X | ||
Special Tools Required | X |
Additional Information | |
*This matrix does not currently contain all production vehicles sold in the United States. The contents are based on OEM vehicle-specific repair information, other OEM-supplied documents available from the vehicle maker, and the I-CAR OEM Linking Pin process. Updates and additions will be posted as they become available. To ensure that you are using the most recent information, always refer to vehicle maker technical information. Information displayed in quotes ("") are direct quotes from the OEM-specific/vehicle-specific information and/or the I-CAR OEM Linking Pin process.