OEM Calibration Requirements Search
2024 Volkswagen Tiguan
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: Rearview Camera
Calibration/Initialization Requirement Events:
- After an axle alignment
- If camera is removed/installed or replaced
- If front or rear axle or axle components are removed/installed or replaced
- If liftgate handle or latch is removed/installed or replaced
- If repairs are made on the liftgate
| Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Left Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Right Peripheral Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, adjusted, or repaired
- If control module is replaced
- If control module software is flashed
- If data is written on the control module
- If overlap range of individual camera is adjusted
- If standing height of one axle changes by more than 5 mm
- If vehicle ride height changes
- If wheel alignment is performed
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Driver Assistance Systems Front Camera
Calibration/Initialization Requirement Events:
- If "no or incorrect basic setting/adaptation" is stored in the event memory
- If camera is removed/installed or replaced
- If DTC indicates
- If level control system sensor control position is reprogrammed
- If level control system sensor is readapted on vehicles with damping regulation
- If rear axle toe is adjusted
- If vehicle ride height changes
- If windshield is removed/installed or replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Control Module for Adaptive Cruise Control
Calibration/Initialization Requirement Events:
- If DTC indicates
- If lock carrier is moved into service position
- If lock carrier is removed/installed or replaced
- If rear axle toe is adjusted
- If sensor is removed/installed or replaced
- If vehicle ride height changes
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: Rear Level Control System Sensor
Calibration/Initialization Requirement Events:
- If leveling sensor is removed/installed or replaced
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Parking Aid Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille (Sides)
OEM Name: Front Parallel Parking Assistance Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)
OEM Name: Lane Change Assistance Control Module
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Quarter Panel Behind Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Parking Aid Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover (Sides)
OEM Name: Rear Parallel Parking Assistance Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |